







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Home Additions & ADU: The Downey Owner’s Guide
We install Schluter-compatible home additions and ADU systems across Downey, and a full addition typically runs $45,000 – $130,000 depending on size, foundation work and finish level. Detached ADUs land between $90,000 and $220,000, and garage conversions between $30,000 and $80,000. Most owners don’t call us because a single part failed. They call because the waterproofing under a new bathroom floor or the uncoupling membrane under tile in a converted garage has started to lift, crack or show efflorescence along the grout lines – and the contractor who installed it isn’t returning calls.

Schluter is a German company, and their systems (DITRA, KERDI, DITRA-HEAT, KERDI-BOARD) are engineered as complete assemblies. When one layer fails, it usually means the whole stack was installed wrong, not that one piece went bad. That’s the honest picture before you spend a dollar.
Key takeaways
- Schluter failures in Downey are almost always installation failures, not product failures.
- We’re an independent service provider. We are not affiliated with Schluter Systems.
- Addition pricing for Downey starts at $45,000 and tops out around $130,000 for a full build.
- Every project carries our 730-Day Done Right Promise.
Which Schluter Models This Applies To

Schluter’s residential systems split into a few families, and knowing which one you have saves a wasted service call:
- DITRA and DITRA-XL – uncoupling membrane for tile. The 3/16″ profile (DITRA) is standard; DITRA-XL runs 5/16″ for thicker tile. Compatible with thinset-modified mortar only.
- KERDI and KERDI-BAND – sheet waterproofing. KERDI comes in 3’3″ and 4’11” widths. The band is 5″ or 7″ wide, and the seam overlap matters: Schluter specs a 2″ minimum overlap on all joints.
- KERDI-BOARD – foam backer board in 1/2″, 3/4″ and 1″ panels. 1/2″ is for walls, 3/4″ is for floors and benches.
- DITRA-HEAT – electric floor warming that locks into the DITRA profile. The heating cable is 1/8″ and needs the correct thermostat (DITRA-HEAT-E-R or -E-RT).
To identify what you have, look at the printed edge of the membrane or the backer board’s stamp. Schluter prints the product name and lot number directly on the fleece. If it’s a thick orange sheet with square grid lines, it’s DITRA. If it’s a thinner orange sheet with no grid, it’s KERDI. Pull a loose corner if you can and measure the thickness with a caliper – that’s how you confirm DITRA vs. DITRA-XL before ordering.
OEM vs. aftermarket for Schluter: skip the aftermarket. There are generic uncoupling membranes sold at big-box stores in Downey, and they typically fail the ANSI A118.10 waterproofing standard that Schluter passes outright. The generics cost a few dollars less per square foot and cost you the entire subfloor when they fail. Original Schluter parts are the only sane choice for a Downey addition or ADU.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Home Additions & ADU Is Failing
Here’s what an owner in Downey actually notices when these systems break down:
- Hollow pops under tile. Tap a tile with a screwdriver handle. A dull thud means the thinset bond broke. Usually caused by unmodified mortar under DITRA, which Schluter explicitly voids.
- Efflorescence on the grout. White crust along grout lines means moisture is moving through the assembly. In Downey’s climate, this shows up in garages converted to ADUs because the slab stays cool year-round and vapor drives up through tile.
- Lifting or curling membrane edges. If the orange sheet peels up at a corner, the fleece bond failed. Common when the slab wasn’t cleaned properly or when installers skipped the KERDI-FIX adhesive at transitions.
- Water at the shower curb or ADU bathroom threshold. Water where it shouldn’t be means the KERDI-BAND seams aren’t lapped correctly. Schluter requires a 2″ overlap; the failure is always at the seam, not the sheet.
- Grout cracks in a straight line. That’s a movement joint that wasn’t honored, or a membrane failure directly over a concrete control joint. The addition’s slab is moving and the tile is picking up the stress.
One honest note: these signs can also point to a failed slab, a plumbing leak, or a bad thinset mix. That’s why we recommend a site evaluation before assuming you need a full tear-out.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what Schluter-related repair and replacement work typically runs for a Downey addition or ADU, installed:
- Targeted tile repair over DITRA (small area): $450 – $1,200
- DITRA or DITRA-XL reinstall (full bathroom floor): $900 – $2,800
- KERDI shower waterproofing redo: $2,200 – $5,500
- DITRA-HEAT repair (cable or thermostat): $600 – $2,400
- Full addition rebuild starting from slab: $45,000 – $130,000
The range depends on square footage, whether the subfloor is sound, and whether we’re replacing one membrane or reconstructing a wet area. We quote upfront, in writing, before demolition. The number you see is the number you pay. No change orders for surprises we found in the wall.
Work is covered by the 730-Day Done Right Promise. If the assembly fails inside two years, we come back and make it right – that includes the Schluter materials, the tile, the labor and the finished floor. Also: $1,000 off projects over $10,000, and 0% financing for 18 months on approved credit.
DIY or Call Us?
Here’s the honest split. You can safely check for hollow tile, photograph the labels on your membrane, and measure whether you have DITRA or KERDI. That’s about it.
The rest isn’t a DIY project, and we’ll say why. Schluter systems fail from the substrate up – the slab has to be flat to a specific tolerance (1/8″ in 10 feet), the thinset has to be the correct type and mix, and the KERDI seams have to be lapped exactly. One skipped step and the whole assembly is compromised. That’s not a warning about skill; it’s a warning about the spec sheets, which are unforgiving. Additionally, pulling up tile over a subfloor that may hide a plumbing leak can turn a $900 repair into a $9,000 one before you realize what happened.
If you’re not sure whether your assembly is failing or just cosmetic, call us at (888) 255-8179. We’ll tell you on the phone what the symptom points to. Live person, around the clock.
FAQs

How long does a Schluter home addition or ADU last? The Schluter membrane itself is rated for the life of the tile assembly – decades, if installed to spec. In Downey, the failure timeline we see is 6 – 11 years, and the cause is always installation shortcuts or slab movement, not the product. Call (888) 255-8179 for an honest read on your specific install.
Can it be repaired instead of replaced? Sometimes. A single tile can be replaced over DITRA without touching the membrane if the bond is intact. If the membrane itself has lifted or the KERDI seams are compromised, spot repair fails within a year – we’ll tell you which situation you’re in after a walkthrough. Call (888) 255-8179 to schedule the free estimate.
How long does the swap take? A targeted repair runs 1 – 2 days. A full waterproofing redo on an ADU bathroom or a kitchen backsplash area over new DITRA runs 4 – 7 working days including cure time. Full addition rebuilds are months, planned out with permits pulled and inspections passed. Call (888) 255-8179 for a real timeline on your scope.
How do you source the Schluter parts? We buy original Schluter from authorized distributors – never the generic big-box substitutes – and we source to the exact product and profile your assembly calls for. We don’t stock parts; every order is made to the job after the eval. Call (888) 255-8179 to get the sourcing conversation started.
Written by the team at Groundwork Construction Co. of Downey, serving Downey and nearby areas.
Groundwork Construction Co. of Downey is an independent service provider. We’re not affiliated with Schluter Systems. We also work with KraftMaid, Cambria and Silestone on kitchen and bath finishes for Downey additions and ADUs – bringing the same written promise, the same upfront pricing and the same live-answered phone line to every project, from foundation to finish line. Call (888) 255-8179 for a free estimate. Estimates are free. Background-checked, uniformed technicians. One contractor, start to finish.












