







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Concrete Driveways & Concrete Work in Santa Fe Springs: What It Takes and What It Costs
Concrete driveways & concrete work in Santa Fe Springs generally run $4,500 – $12,000 for a new driveway pour, with most single-car aprons and standard two-car runs landing in the $6,000 – $9,000 range. A typical job takes 3 to 5 days from demo to the day you can park on it, and a full replacement with new base and hauling usually lands at $5,000 – $14,000. Call (888) 255-8179 for a free on-site estimate and a written line-item quote.
How a Concrete Driveway Job Actually Runs, Start to Finish

Five stages, and you make one real decision at each. Here’s the sequence we follow so you know what’s happening on your property and when.
Stage 1: Site walk and layout (day one, 1 – 2 hours)
We mark the apron, measure slopes away from the garage, and confirm where the sidewalk, meter box, and gas line sit. You decide on finished width, thickness, and whether the driveway runs straight or flares at the street. On older Santa Fe Springs lots off the 605 side, this is also when we check for the original concrete apron still sitting under the current surface – a common find in the 1950s ranch pockets.
Stage 2: Demo and haul-off (day one to day two)
The old slab comes out with a skip loader and jackhammer, and we haul the rubble the same day. A standard 400-square-foot driveway is roughly 5 to 6 tons of debris. You don’t decide anything here, but you do get a clear look at what’s underneath: root intrusion, buried utility lines, or soft fill that will change the base spec.
Stage 3: Base prep and grading (day two, full day)
We excavate 6 to 8 inches, compact the subgrade, and lay 4 inches of Class II base rock. This is the part that gets skipped on cheap bids and it’s the part that decides whether your driveway cracks in three years. You decide here whether to add a swale or trench drain if the driveway pools water at the garage threshold.
Stage 4: Forming, rebar, and pour (day three, full day)
Forms go up, #3 or #4 rebar goes in on a 16 – 24 inch grid, and we pour 4 inches of 3,000- to 3,500-PSI mix, 5 inches if you regularly park a truck or trailer. Expansion joints go in against the garage and sidewalk. You decide the finish: broom, exposed aggregate, or a light salt finish.
Stage 5: Cure and sealing (day four to day five, then 7 days of light traffic)
We cut control joints within 24 hours, strip forms on day two after the pour, and apply a cure-and-seal coat. You can walk on it in 24 hours, drive on it in 7 days, and park heavy vehicles after 10. Full cure is 28 days, and that’s the number that matters for strength.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
What You’ll Choose Between on a Santa Fe Springs Pour
- Standard broom finish: The workhorse and the least expensive. Good traction, hides small imperfections, and the right call for most residential driveways. Downside is it shows oil stains and tire marks over time.
- Exposed aggregate: Pebble surface revealed by a retarder wash. More slip-resistant and hides dirt better than broom, but adds roughly 15 – 25% to the pour cost and is harder to patch if it ever spalls.
- Stamped or decorative concrete: Textured to read like pavers or slate. Looks sharp on a front approach. It costs noticeably more, and in Santa Fe Springs sun it needs resealing every 2 – 3 years to hold color.
- Plain gray vs. integral color: Gray 3,000-PSI mix is standard. Adding integral color or a colored hardener runs $1 – $3 more per square foot and gives a warmer look without the maintenance of a surface stain.
- Reinforcement choice: Rebar, wire mesh, or fiber mesh. Rebar holds the slab together across cracks; fiber mesh reduces surface micro-cracking but doesn’t replace steel. We recommend rebar on any drive over 12 feet wide.
- Thickness: 4 inches for cars, 5 to 6 inches where a truck, trailer, or RV parks. Going thicker costs more on concrete but saves a re-pour later.
We mix Quikrete bagged product on smaller aprons and walkway tie-ins, and we use ready-mix for anything over a couple of yards. You’ll see the mix design in writing on your estimate.
What Concrete Driveways & Concrete Work Costs in Santa Fe Springs, CA

For a new pour driveway, expect $4,500 – $12,000. A full driveway replacement, including demo and haul-off, runs $5,000 – $14,000. Sealing an existing slab is $250 – $700. Here’s what moves the number:
- Size and thickness: A 300 sq ft single-car apron sits at the low end. A 600 sq ft two-car run with a 5-inch slab for a truck pushes to the high end.
- Existing condition: A clean slab over intact base is a straightforward pour. Broken-up concrete with root intrusion or a failed base adds demo, hauling, and re-excavation.
- Access: Tight side yards and driveways hemmed in by block walls or mature trees slow the machinery and add labor hours.
- Base and drainage work: Adding a drain trench, swale, or re-grading to move water away from the garage adds cost but solves the pooling problem you probably already have.
- Permit scope: A driveway pour that widens the apron or crosses a public sidewalk triggers a city permit and inspection, which adds time and a fee. A like-for-like replacement in the same footprint is often exempt; we confirm on the site walk.
Your written estimate lists concrete yards, PSI, rebar spec, base depth, demo, haul-off, permit responsibility, and sealing. It doesn’t include unforeseen utility relocation or a root-and-stump grind if we find one under the slab, and we flag those before we start rather than after.
See the difference
Before
After
Before
After
Before
AfterWhat Santa Fe Springs Homes Specifically Do to This Job
Most of the housing in Santa Fe Springs went up between the late 1940s and the 1970s, which means the concrete we’re tearing out was often poured when Eisenhower was president. Those 1950s ranch homes on small lots behind the 605/5 interchange usually have a shallow, thin slab with no reinforcement and no proper base – rebuild it and the failure mode repeats. We’re pouring on ground that sits in the Whittier Narrows, and the hot inland summers bake a bare slab, while the fall Santa Ana winds cycle exterior concrete between heat and windblown grit. The truck traffic off the rail yards and warehouses coats everything in fine dust, which works into unsealed control joints and drives freeze-thaw-like wear even in Southern California. On the permitting side, a residential driveway replacement inside the same footprint is straightforward, but widening the apron or crossing a public sidewalk brings in the City’s design review and inspection process – the same counter that adds months to industrial projects. Every new pour also has to comply with California’s seismic provisions, so if the driveway abuts a detached structure, we check the framing and footing tie-ins too. When a driveway job is part of a full Driveway & Pavers in Santa Fe Springs project combined with walkways or a front approach, we coordinate the poring schedule so you’re not living on dirt for an extra week.
Serving Santa Fe Springs, CA – Our Local Coverage Area
We serve Santa Fe Springs and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Concrete Driveways & Concrete Work in Santa Fe Springs

Plan on 3 to 5 days of active work, then 7 days before you drive on it and about 28 days for full cure. The weather rarely slows us here – heat actually helps the cure – but a permit for a widened apron can add 2 to 4 weeks before demo even starts. Call (888) 255-8179 for a timeline tied to your specific lot.
A like-for-like replacement in the existing footprint usually doesn’t trigger a permit, but widening the apron, changing the sidewalk, or crossing the right-of-way does. We confirm the permit scope on the site walk and pull what’s needed before the first day of work. Call (888) 255-8179 and we’ll tell you straight whether your job needs one.
New concrete driveways run $4,500 – $12,000, and a full replacement with demo runs $5,000 – $14,000. The number depends on square footage, slab thickness, base condition, and whether the apron width changes. Call (888) 255-8179 for a free estimate with line-item pricing.
Not on a fixed written quote unless we uncover something no one could see before demo – a collapsed base, a buried utility, or root intrusion under the slab. Those get priced before we keep going, in writing, with your approval. The number on the estimate is the number you pay for the scope we agreed to. Call (888) 255-8179 to get that quote scheduled.
Every groundworks project is covered by the 730-Day Done Right Promise – if the workmanship isn’t right, we make it right. That covers settling, base failures, and finish defects from our install, and it runs two full years. Call (888) 255-8179 to talk through what your project will be covered for before you commit.
Get a Free Concrete Driveway Estimate in Santa Fe Springs
Concrete driveways & concrete work in Santa Fe Springs start with a site walk and a written line-item quote, and both are free. Call (888) 255-8179 and a live person answers 24/7 – tell us the driveway size, whether you need demo, and whether you want a plain gray or decorative finish. We’ll schedule the walk, spec the pour, and hand you a number in writing. If you’re also considering a Garage Conversion ADU in Santa Fe Springs or a New Detached ADU in Santa Fe Springs, we time the pour around the framing so the driveway doesn’t have to be redone. Groundwork Construction Co. serves all of Santa Fe Springs and surrounding neighborhoods, and our driveway & pavers service is part of the seven core service lines we run.
Written by the team at Groundwork Construction Co.












