







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Aluminum Fence in Whittier: What It Costs and How Long It Takes
An aluminum fence installation in Whittier typically runs $4,000 to $10,000, and most residential yards are finished in 2 to 4 days once materials are on site. You’re buying a powder-coated, rust-proof barrier that holds its finish through hot basin summers rather than a wood fence that needs staining every few years. The number that matters is the written, line-item quote, and you can get one by calling (888) 255-8179. Estimates are free and there’s no pressure to sign anything on the spot.
How an Aluminum Fence Goes In, Stage by Stage

Aluminum fence work is less forgiving than wood because every post has to land in a straight, level line. There’s no flexing a panel to hide a bad set. Here’s the actual sequence we run.
1. On-site measure and layout (day 1, about 90 minutes)
We walk the property line with you, confirm where the fence should sit relative to your lot line, and mark post locations. This is where you decide one of the biggest cost levers: straight runs versus corners and grade changes. A flat back line is fast. A yard that steps down a slope needs racked panels or stepped sections, and that changes the panel count and the labor.
2. Utility locate and permit check (day 1 to day 3)
Before anything gets dug, 811 markings go in so we don’t hit irrigation lines, gas, or buried electrical. If your fence crosses a property line you share with a neighbor, or sits in a front setback, Whittier may require a permit and a plot plan. We tell you up front whether your job needs one, because pulling it after posts are set is a mess.
3. Demo and prep (day 2, half to a full day)
Old fencing comes out, concrete footings get broken and hauled, and the line gets cleared. If there’s an existing chain link with embedded posts, those get cut flush or pulled entirely, depending on what you want underneath. This is the dirtiest part of the job and the one homeowners most often underestimate.
4. Post setting (day 2 to day 3)
Posts go into concrete footings set below the frost-free depth for our region, plumb and on string line. Aluminum posts are lighter than steel but they still need proper footing depth and diameter or the whole run will lean within a season. Cure time matters: we don’t hang panels on green concrete.
5. Panel and gate hang, final walk (day 3 to day 4)
Panels get racked to follow grade, gates get hung and adjusted for latch alignment, and we walk the whole run with you. You’ll check gate swing, post plumb, and finish condition before we call it done. Any panel or gate that doesn’t sit right gets corrected before we leave.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Actually Choose Between
Most of the decisions on an aluminum fence happen before a shovel touches dirt. Here’s what moves the look and the price.
- Residential-grade vs. heavy-duty aluminum. Standard residential panels are lighter and cost less, fine for a backyard boundary. Heavy-duty extruded aluminum has thicker walls and a stronger weld at the Pickets, and it’s the right call for a street-facing fence or a yard with dogs that lean on the rail.
- Picket spacing and height. Standard 4-foot and 5-foot heights cover most yards. Tighter picket spacing (under 4 inches) keeps small dogs in and looks more ornamental; wider spacing costs less per panel but reads more industrial.
- Powder-coat finish and color. Black is the default and the most forgiving of dust. Bronze and architectural white are available but can carry a longer lead time. A quality powder coat is what keeps aluminum from chalking in the sun; a cheap finish is where budget fencing fails first.
- Flat-top vs. pressed-point or spear-top. Decorative tops add cost per panel but give a wrought-iron look without the rust. Plain flat-top is the most economical and the easiest to maintain.
- Gate type. A self-closing pedestrian gate with a keyed latch is standard; a double-drive gate is a different animal entirely and adds significant cost, hardware, and often a permit.
What Aluminum Fence Costs in Whittier, CA

For a typical residential yard in Whittier, aluminum fence installation lands between $4,000 and $10,000. Here’s what pushes a job toward one end or the other.
- Linear footage and post count. The single biggest driver. More corners and grade changes mean more posts and more panels.
- Site access and demo. A yard with an existing fence, mature trees on the line, or tight side-yard access takes longer to clear and adds to labor.
- Grade and terrain. A flat lot is straightforward. A sloped or stepped yard needs racked panels, stepped sections, or both.
- Finish and gauge. Heavy-duty extruded aluminum with a premium powder coat sits at the top of the range; standard residential panels sit at the bottom.
- Permit scope. Front-yard or property-line fencing may need a permit and plot plan; that’s a line item on the estimate, not a surprise later.
A written estimate should spell out footage, panel type, post spacing, footing spec, gate hardware, demo and haul-away, and permit fees if any apply. What it typically doesn’t include: repairing damaged irrigation lines we uncover, replacing a gate opener, or landscaping restoration after demo. We flag anything we find before we touch it.
See the difference
Before
After
Before
After
Before
AfterWhat Whittier Homes Do to This Job
Whittier’s housing stock splits hard, and it changes how an aluminum fence gets built. Around the Uptown core and the historic overlay, you’re working behind 1920s Craftsman bungalows and stucco Spanish Colonial Revival homes, where a front-yard fence can trigger design review and a plot plan before a single post goes in. Across the eastern tracts, the mid-century ranches on slab-on-grade often have original irrigation and old chain link already in the ground, which means more demo and more utility surprises. Homes in the 90603 and 90605 ZIPs frequently sit on lots with existing fences to the property line, so we confirm shared-line placement with neighbors early. Then there’s the climate: hot, dry basin summers and Santa Ana wind episodes bake stucco and dry out anything porous, which is exactly why a powder-coated aluminum fence holds up here better than wood. If your project grows into something larger, it’s often part of a full Fence Installation in Whittier, and homeowners frequently pair new fencing with Driveway Repair & Replacement in Whittier or Patios, Walkways & Pool Decks in Whittier while the yard is torn up anyway.
Serving Whittier, CA – Our Local Coverage Area
We serve Whittier and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Aluminum Fence in Whittier

Most residential aluminum fence jobs in Whittier run 2 to 4 days on site once materials arrive, with permit review adding time if your fence needs one. A simple flat backyard run is often done in 2 days; a yard with demo, slopes, or a double gate takes closer to 4. Call (888) 255-8179 and we’ll give you a realistic timeline for your specific yard, not a generic one.
It depends on height, location, and whether it sits in a front setback or near a property line; front-yard or taller fences commonly require a permit and plot plan. Around the historic overlay near Uptown, design review can add time that wouldn’t apply to a mid-century tract home across town. We check your specific address before quoting and tell you plainly what applies.
Yes, upfront: aluminum typically runs higher than a basic wood fence, but it doesn’t need staining, won’t rot, and won’t dry-crack in our summers, so the long-term cost of ownership often comes out lower. For Whittier’s climate, that durability is the real argument for aluminum. Call (888) 255-8179 for a line-item quote so you can compare apples to apples.
Usually yes. Aluminum posts go in along the line, so unless we hit buried irrigation or utilities, existing patios, planting beds, and structures stay untouched. We confirm utility locates and layout before digging, so surprises get caught first. If your project is wider in scope, our Fence Installation team covers the broader work, and we serve the whole Whittier area.
Workmanship is backed by our 730-Day Done Right Promise: if it isn’t done right, we make it right. Manufacturer finish warranties vary by panel line, and we spell out exactly what’s covered in your written estimate. Materials come from verified brand partners, so you know what you’re getting.
Get a Free Aluminum Fence Estimate in Whittier
Call (888) 255-8179 to schedule a free on-site estimate for your aluminum fence in Whittier. A live person answers around the clock, we walk your property line with you, and you leave with a written, line-item quote and a clear timeline. No pressure, no vague bids, and pricing you can plan around.
Written by the team at Groundwork Construction Co.












