







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Blanco Kitchen Remodeling: The Downey Owner’s Guide
Blanco kitchen remodeling work in Downey usually runs $14,000 – $45,000 for a full kitchen, with smaller single-element projects like a sink swap, countertop cut-out or cabinet refit landing well below that. Blanco is best known for its sinks and faucets, so most of what we install around the Blanco name is the sink-and-faucet package set into new counters or cabinetry. We’re an independent service provider, not affiliated with Blanco.

Owners rarely call us because a Blanco part failed on a schedule. They call because a Silgranit sink has gone chalky after years of Downey’s hard water, a faucet cartridge has started dripping at the base, or a sink has loosened from its cut-out and the seal underneath has gone soft. That’s the moment the search starts: what fits my model, what does it cost, and who installs it without turning a two-hour job into a two-week one.
Key Takeaways
- Full Blanco-inclusive kitchen remodels in Downey: $14,000 – $45,000.
- Cabinet installation alone: $4,000 – $13,000. Countertop installation: $2,000 – $6,500.
- Blanco model number lives on a label under the sink rim or on the faucet body – measure before you order anything.
- Every project is backed by our 730-Day Done Right Promise.
Which Blanco Models This Applies To

Blanco’s kitchen line splits into three families you’ll run into in Downey homes: Silgranit sinks (the granite-composite drop-ins and undermounts, sold in series like Diamond, Valea and Precis), stainless steel sinks (Quatrus, Formera, Radius), and faucets (Liven, Arte, Empressa, Sonus, Urbena). The part that fails depends entirely on which family you own, and that’s the first thing to nail down.
Here’s the compatibility gotcha most owners miss: Silgranit sinks are molded to a specific bowl depth and drain hole size, and older Diamond-series models use a different drain fitting than current stock. If you order a replacement strainer or disposal flange by brand name alone, there’s a real chance it won’t seat. Same story with faucets: cartridge assemblies differ across generations of the same model name, so the year your faucet was built matters as much as the model stamp.
Find the label. On sinks it’s a sticker or molded mark on the underside of the bowl near the drain. On faucets it’s usually stamped on the shank under the counter or on the base ring. Photograph it, measure the bowl length, width and depth in inches, and note whether it’s undermount or drop-in. That five-minute step decides whether you’re buying OEM or a quality aftermarket equivalent.
The OEM-versus-aftermarket call for Blanco is straightforward. For visible parts – the sink itself, a faucet body – OEM protects the finish and the fit. For internal wear parts like cartridges and seals, a quality aftermarket equivalent from a name-brand supplier often works and costs less, but only if the spec matches. We verify fit against your model before anything gets ordered.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Blanco Kitchen Remodeling Is Failing
- Chalky white film on a Silgranit bowl that won’t scrub off. That’s mineral scale from Downey’s hard water bonding to the composite surface. It’s cosmetic at first, but repeated scale buildup dulls the finish permanently if it’s never addressed.
- A drip at the faucet base or spout that continues after the handle is fully closed. Usually a worn cartridge or seat. In a ceramic-disc faucet this is almost always the cartridge, not the whole fixture.
- Water seeping around the sink rim onto the countertop. The plumber’s putty or silicone seal under the rim has failed. Left alone, water tracks into the cabinet below and softens the substrate.
- A sink that rocks or flexes when you press on it. The mounting clips have loosened or the cut-out wasn’t sized correctly to begin with. This is common in older Downey kitchens where a sink was swapped without re-fitting the opening.
- Standing water or a slow drain at the sink base. Often a degrading tailpiece gasket or a disposal flange that’s worked loose. Small leak, big damage over a year of drip.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Downey, here’s what Blanco-related work actually runs, installed:
- Cabinet installation (new boxes or refacing): $4,000 – $13,000
- Countertop installation (including the sink cut-out and fit): $2,000 – $6,500
- Kitchen island installation: $3,000 – $10,000
- Backsplash installation: $800 – $2,500
- Full kitchen remodel with a Blanco sink-and-faucet package: $14,000 – $45,000
What drives the range: the sink itself (Silgranit runs higher than stainless), whether the existing cut-out needs resizing, countertop material, and whether the faucet swap exposes old supply lines that need replacing. You get a written line-item quote before anything starts – the number you see is the number you pay, with no change orders appearing mid-job. Labor and materials are broken out separately, and all the work carries our 730-Day Done Right Promise, backed in writing.

Financing is available at 0% for 18 months, and projects over $10,000 take $1,000 off. The estimate and design consult are free. If you’re pairing the Blanco package with KraftMaid cabinetry or a Cambria or Silestone counter, we carry those lines too, so the whole kitchen moves through one contractor instead of three.
DIY or Call Us?
Some checks are safe to do yourself: photograph the model label, measure the bowl, verify whether the sink is undermount or drop-in, and confirm the faucet cartridge part number against your fixture. Those steps cost nothing and tell you exactly what you’re dealing with.
Where DIY goes wrong on a Blanco install is the fit and the seal. Sink cut-outs have no margin – a cut-out that’s off by an eighth of an inch means a sink that rocks or leaks at the rim, and correcting it means reworking the counter, not the sink. Faucet cartridge swaps go sideways when the wrong-generation part is forced into place and the valve body gets scored, which turns a $40 part into a fixture replacement. That’s the point where it stops being a Saturday project.
Our technicians have up to 12 years of experience on kitchen work and are background-checked, arriving in uniform. Call (888) 255-8179 and we’ll confirm fit against your Blanco model before you spend a dollar on parts.
FAQs

Expect 10 to 15 years of regular use in Downey’s water conditions, with the finish holding up longer if scale is cleaned regularly rather than left to bond. The composite itself rarely cracks; it’s the surface finish and the drain fittings that age first.
Often yes. A dripping Blanco faucet is usually a cartridge replacement, not a new fixture, and a slightly loose sink can sometimes be re-clipped and re-sealed rather than swapped. We look at repair first whenever the bowl and finish are sound. Call (888) 255-8179 and we’ll tell you honestly which way to go.
A faucet cartridge replacement or a straight sink swap typically finishes in a single visit of a few hours. A swap that requires resizing the counter cut-out or reworking the cabinet top adds a day or more once the counter is involved. We confirm the scope and timing on the quote before scheduling.
We match the part to your model number and generation, then source from OEM or a vetted aftermarket supplier depending on the part and the fit. You approve the part and price before we order. If it doesn’t fit on arrival, that’s on us, not you.
Call (888) 255-8179 to schedule your free estimate. Live person, 24/7 – no voicemail, no waiting until Monday.
Written by the team at Groundwork Construction Co. of Downey, serving Downey and nearby areas.












