







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Kitchen Remodeling: The Downey Owner’s Guide
Boral doesn’t make kitchen cabinets or countertops, and that surprises most Downey homeowners who land here. Boral is a building materials manufacturer best known for roof tile, brick, stone veneer and trim, so “Boral kitchen remodeling” almost always means one of two things: a Boral stone veneer or brick feature wall going into a kitchen remodel, or a homeowner who’s confusing the Boral label on their backsplash or accent material with the cabinet or countertop brand. Installed kitchen remodeling in Downey runs $14,000 – $45,000, and a small kitchen remodel sits at $9,000 – $20,000. Owners usually find the problem the same way: a stone accent that’s come loose above the range, grout cracking along a Boral-clad backsplash, or discoloration on a veneer wall behind the cooktop after a few seasons of steam and grease. We’re an independent service provider, not affiliated with Boral, and we install and repair the full kitchen scope around these materials.

Key Takeaways
- Boral makes masonry and stone products, not cabinets or countertops. If your kitchen remodel involves a Boral accent, we handle the whole job: demolition, substrate, stone, cabinets, countertop and finish.
- Boral veneer in a Downey kitchen fails most often from moisture behind the stone and heat cycling near the range, not from the stone itself.
- Full kitchen remodels here run $14,000 – $45,000. Cabinet installation alone is $4,000 – $13,000, countertops $2,000 – $6,500, backsplash $800 – $2,500.
- We’re upfront on pricing: the number you see is the number you pay, and every project carries our 730-Day Done Right Promise.
Which Boral Products This Applies To

Boral’s kitchen-relevant catalog is narrower than most people assume. The lines you’ll actually encounter in a Downey kitchen are Cultured Stone veneer (ledgestone, country ledgestone, cut cobble), Boral thin brick for a feature wall or range hood surround, and Boral trim and moulding for cabinet crown and peninsula detailing. If you’re holding a Boral label from a backsplash tile, read it carefully: most backsplash tile sold in Downey is ceramic, porcelain or natural stone from other manufacturers, and a Boral stamp on a box is more likely the thin brick or veneer carton than the tile itself.
Identify your material before ordering anything. Look for the carton label or the printed stamp on the back of a loose piece. Boral Cultured Stone pieces are typically 6 to 24 inches in face length and roughly 0.75 to 1.5 inches thick, and they’re installed as veneer over a substrate, not as structural masonry. Thin brick runs about 0.5 inch thick. Get the series name and the color lot off the label, because Boral stone is produced in dye lots and a replacement ordered two years later can read visibly cooler or warmer next to the original run. That lot mismatch is the single most common compatibility gotcha on these jobs, and it’s why we photograph the label and lot code on every Boral kitchen we touch.
On the OEM-versus-aftermarket question: for Boral veneer and thin brick, stay with Boral or an exact-profile equivalent. The color and texture mismatch on a generic substitute shows from across the room, especially under the warm 2700K to 3000K lighting most Downey kitchens run. Our technicians have up to 12 years of experience setting these materials, and we quote the exact product and lot match in writing before anything is ordered.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Boral Kitchen Remodeling Is Failing
Boral stone and thin brick are durable materials, but the assembly around them fails first. Here’s what Downey owners report, and what’s actually going on underneath:
- Stone lifting or hollow-sounding when tapped. The bond between the veneer and the scratch coat has broken down, usually from moisture trapped behind the stone because the flashing or weep detail was skipped. In Downey’s dry summers and damp winter mornings, that trapped moisture expands and contracts until the bond lets go.
- Grout lines cracking along a backsplash or feature wall. Movement, not bad grout. Kitchen walls flex with heat from the range and with the seasonal swing in a slab-on-grade home, and rigid grout over a flexible substrate cracks at the stress points.
- Efflorescence, the white chalky bloom on the stone face. Salts migrating out of the masonry as moisture moves through it. It’s a moisture-path problem, and wiping it off doesn’t fix the source.
- Discoloration or grease staining behind the cooktop. Boral veneer is porous enough that airborne cooking grease settles into the texture and doesn’t scrub out. In Downey kitchens where the range sits against a stone wall, we see this within two to three years of daily cooking.
- Thin brick spalling or flaking at the corners. Freeze-thaw isn’t the driver here, but repeated steam exposure and a missing sealant can cause face flaking on thin brick near a sink or hood. Once the face is gone, the piece has to be replaced, not patched.
Replacement Cost & What’s Included

If the Boral work is part of a larger kitchen remodel, budget $14,000 – $45,000 for the full job in Downey, or $9,000 – $20,000 for a small kitchen. If you’re isolating the pieces, here’s how the line items break down:
| Scope | Installed Range |
|---|---|
| Full kitchen remodel | $14,000 – $45,000 |
| Small kitchen remodel | $9,000 – $20,000 |
| Cabinet installation | $4,000 – $13,000 |
| Countertop installation | $2,000 – $6,500 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island installation | $3,000 – $10,000 |
What drives the range: square footage of stone or thin brick, whether the substrate has to be rebuilt or just re-bonded, whether the lot matches your existing run, and whether the job pulls a permit. Downey projects that touch electrical or plumbing behind the wall need inspection, and we pull the permits and pass the inspections. Our pricing is upfront, so the number you see is the number you pay, and there are no change orders for work we scoped. Every job is backed by our 730-Day Done Right Promise: if it’s not done right, we make it right. We also take $1,000 off projects over $10,000 and offer 0% financing for 18 months.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
You can safely check a few things yourself. Tap the stone with a screwdriver handle and listen for hollow spots. Look for hairline cracks in the grout at inside corners. Check whether the caulk joint where the stone meets the countertop has separated. Photograph the carton label and lot code if you still have it. None of that is risky and it tells us a lot before we arrive.
Where DIY goes wrong on Boral veneer is the re-bond itself. Setting stone over a failing scratch coat without addressing the moisture path behind it just puts new stone on a bad wall, and it lifts again within a season. On thin brick around a range hood or an outlet, cutting and re-setting near live wiring is where homeowners get hurt. We’d rather you not take that on. Call (888) 255-8179 and a live person answers, any hour, any day. The estimate and design consult are free.
FAQs

The stone itself lasts decades. The installation around it is what sets the real lifespan, and a properly flashed, properly bonded Boral veneer in a Downey kitchen typically holds up 20 years or more, while a poorly detailed one can start lifting in 5 to 8. Our 730-Day Done Right Promise covers the workmanship on anything we install. Call (888) 255-8179 for a free assessment of what you have.
Often yes. Individual loose pieces can be re-bonded, and grout or caulk joints can be renewed without tearing out the wall, if the substrate behind the stone is still sound. The repair only works when the moisture source is corrected at the same time. If the scratch coat has failed across a whole section, replacement is the honest answer. Call (888) 255-8179 and we’ll tell you which one you’re looking at.
A localized repair, a few pieces plus grout, is typically done in a single visit. A full backsplash or feature wall replacement runs two to four days once materials are on site, and lead time on a matched Boral lot is usually the longer part. Full kitchen remodels in Downey run several weeks depending on scope. Call (888) 255-8179 to get a timeline for your specific job.
We match by series name and lot code, not by eyeballing the color. Your carton label or a photo of the back stamp gives us the series, and we order against the closest available lot, then set a sample against your existing run before committing the whole order. We don’t carry parts on a truck and we don’t stock Boral locally; every piece is ordered to your job so the match is right. Call (888) 255-8179 and we’ll start with a free estimate.
Building Your Downey Kitchen Around Quality Materials
If your Boral accent is the starting point for a bigger Downey remodel, we handle the full scope from foundation to finish line: cabinets, countertops and the stone work, all under one contractor. Alongside Boral we install KraftMaid cabinets, Cambria and Silestone countertops, and we coordinate the trades so the stone isn’t fighting the cabinet install schedule. Our technicians arrive background-checked and in uniform, and every project is covered by the 730-Day Done Right Promise. Built to last, backed in writing.
Call (888) 255-8179 to schedule your free estimate. A live person answers 24/7, and we’ll walk your kitchen, confirm the Boral product you have, and put a written, upfront price in your hands with no surprises.
Written by the team at Groundwork Construction Co. of Downey, serving Downey and nearby areas.












