







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Chain Link Fence in Santa Fe Springs, CA: What It Costs and How Long It Takes
A chain link fence in Santa Fe Springs typically runs $3,500 to $9,000 installed, depending on linear footage, height, gauge, and how much gate hardware you add. Most residential runs of 150 to 300 feet finish in one to three days, with the permit and the pre-inspection walk taking the longest lead time before we ever break ground. Call (888) 255-8179 and we’ll give you a straight number for your lot, not a range that balloons once the crew shows up.
That price covers posts, fabric, top rail, tension bands, concrete footings, and hauling off the old material. Gates, height above six feet, and sloped or rocky runs push it toward the top. An honest quote takes a walk of the property line, a look at the soil, and a conversation about what the fence has to do: keep a dog in, mark a property line, or screen a work yard from the street.
How the job actually runs, stage by stage

Chain link is a simple fence when it’s done right and a wobbly headache when it isn’t. The sequence matters more than the material. Here’s what a real install looks like.
1. Site walk and property-line confirmation (day 0)
Before a single post goes in, we walk the line with you and confirm where the property boundary actually sits. On the older small-lot tracts off Norwalk Boulevard and Pioneer, fence lines sometimes drift a foot or two from the platted boundary after decades of repairs. If there’s any doubt, we recommend a survey before we set posts. That one decision protects you from a neighbor dispute later, and you make it here.
2. Permit and utility locate (days 1 to 5)
We pull the fence permit where the City requires one and call for utility locates so nobody drives a post through a gas or water line. This is the stage with the most waiting, and it’s the stage most homeowners underestimate. Once the locates come back marked, we schedule the dig.
3. Layout and post setting (day 1)
We stretch a string line, mark every post at even spacing (typically 8 to 10 feet), and dig each hole. Posts get set in concrete footings and need to cure before fabric goes on. Terminal posts at corners, ends, and gate openings get larger footings because they carry the tension of the whole run.
4. Rails, fabric, and gates (day 2 to 3)
Top rail, tension bands, and chain link fabric go up next, pulled tight and tied off. Gates get their frames hung and swing-tested. This is the day the fence starts looking like a fence, and it’s also when your gate placement decisions get locked in, so tell us early if you want a double drive gate or a walk gate on a specific side.
5. Walkthrough and clean-up (final day)
We walk the finished line with you, check tension, gate swing, and footing height, and clean the site. Any adjustment happens then, not a week later after you’ve called twice.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The options you’ll choose between
Chain link is not one product. What you pick here decides how the fence looks in year ten and how much it costs now.
- Gauge of wire: 11.5-gauge is the residential standard and holds up fine. 9-gauge is heavier, resists a big dog leaning on it, and costs more per foot. 12.5-gauge is the thin, builder-grade material you’ll see on cheap bids; it dents and sags faster.
- Height: 4 feet is common for a front-yard boundary, 5 to 6 feet for backyards and pets. Anything over 6 feet usually needs a permit and sturdier posts.
- Coating: Galvanized steel is the honest workhorse and affordable. Vinyl-coated (color-matched green or black) hides the industrial look and adds years against rust, at a modest premium per linear foot.
- Framework: Standard top rail and tension bands versus a heavier “industrial” frame with a bottom rail. The bottom rail keeps dogs from pushing under and firms up the whole run.
- Gates and hardware: A walk gate, a double drive gate, or a rolling gate for a wide opening. Self-closing hinges and a good latch are worth the small upcharge if kids or pets are the reason for the fence.
We don’t push the heaviest option. We ask what the fence has to do and size the material to that, whether you’re fencing a backyard for a dog or screening a side yard from the truck traffic on the adjacent parcel.
What Chain Link Fence costs in Santa Fe Springs, CA

Expect $3,500 to $9,000 for a typical residential chain link fence in Santa Fe Springs. A short 100-foot galvanized run on flat ground lands near the bottom. A 300-foot vinyl-coated run with a double drive gate, on uneven ground, pushes toward the top.
Here’s what moves the number:
- Linear footage: The single biggest driver. Price is quoted per linear foot, so twice the fence is roughly twice the cost.
- Height and gauge: Going from 4-foot 11.5-gauge to 6-foot 9-gauge adds real money in both material and heavier posts.
- Ground conditions: Flat, clear soil is easy. Roots, buried concrete, or a hard slope mean more digging and sometimes stepped panels.
- Gate count and type: Each gate is a line item. A wide rolling gate costs more than a walk gate.
- Removal of the old fence: Tearing out and hauling an existing fence is a separate charge, and old concrete footings are the slow part.
Your written estimate lists footage, gauge, coating, post spacing, gate count, removal, and permit cost as separate lines. What it won’t hide: footing depth, haul-off, and clean-up. Those are in the number. If a bid is dramatically lower than the others, ask what gauge and what footing depth it assumes.
See the difference
Before
After
Before
After
Before
AfterWhat Santa Fe Springs homes specifically do to this job
Santa Fe Springs is a working town with homes tucked in among it. The 1940s-to-1970s ranch houses on small lots sit right next to warehouses, truck yards, and rail lines off the 5 and 605, and that shapes fence work here in ways it doesn’t in a bedroom suburb. Fences along a commercial or industrial parcel line often need a heavier frame and a conversation about screening, because a light residential run won’t hold up to the dust and vibration from constant truck traffic. The Santa Ana winds each fall test every post and rail, so footing depth and post spacing aren’t places to cut corners.
Permitting is its own story. The City runs a real planning counter, and fence requirements near a commercial boundary or a corner lot can differ from a plain interior lot, so we confirm before we dig. On the residential side, the older homes in the 90670 ZIP frequently have original galvanized plumbing and settled soil along the property line, which means post holes sometimes hit old utility runs we locate first. If your project is part of a full Fence Installation in Santa Fe Springs plan, we sequence the chain link with the rest so it reads as one job. Homeowners often pair a new line with Concrete Driveways & Concrete Work in Santa Fe Springs so the gate landing and the drive get finished together, and some do the same with Asphalt Driveways & Resurfacing in Santa Fe Springs where the fence meets the drive.
Serving Santa Fe Springs, CA – Our Local Coverage Area
We serve Santa Fe Springs and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Chain Link Fence in Santa Fe Springs

Most residential chain link fences take one to three days of on-site work once the permit and utility locates clear. The install itself is fast; the waiting on approvals is what stretches the calendar, so budget a couple of weeks total from signed estimate to finished fence. Call (888) 255-8179 for a timeline on your specific lot.
It depends on height and location, and often yes for anything over the standard residential height or near a corner or commercial boundary. We check the requirement with the City before we order material and pull the permit where it’s needed. Call (888) 255-8179 and we’ll tell you what your property needs.
Yes, in most cases. We call for utility locates before digging so we don’t hit buried lines, and setting posts doesn’t touch your plumbing, electrical, or house structure. Call (888) 255-8179 to line up the locate and the schedule together.
A typical residential run costs $3,500 to $9,000, with the exact number set by footage, height, gauge, coating, and gate count. Removal of an old fence is quoted separately. Call (888) 255-8179 for an exact written quote – the estimate is free and it’s itemized.
Every install is backed by our 730-Day Done Right Promise: if it isn’t done right, we come back and make it right for two full years. That covers the workmanship, the footings, and the gate hardware we install. Call (888) 255-8179 to schedule your free estimate.
Get a free chain link fence estimate in Santa Fe Springs
We’ll come out, walk your property line with you, and hand you a written, itemized number for a chain link fence in Santa Fe Springs. A live person answers the phone around the clock, so call (888) 255-8179 whenever it’s convenient. You’ll get an honest quote, a real timeline, and a background-checked crew in uniform on the day of the job. Explore our full Fence Installation work or see how we cover Santa Fe Springs.
Written by the team at Groundwork Construction Co.












