







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in South Whittier, CA: What It Costs and How Long It Takes
An iron fence in South Whittier typically runs $3,500 to $9,000 for most residential jobs, with the average landing around $5,500 to $6,500 for 100 to 150 linear feet of painted steel or wrought iron. Plan on 4 to 6 working days from layout to final touch-up, plus a few weeks of lag time if we’re pulling a LA County permit. Call (888) 255-8179 for a free, no-pressure on-site estimate.
Step by Step: How We Build an Iron Fence in South Whittier

We don’t wing this. Iron fence work is precise, and the sequence below is what you should expect if you hire us or anybody else worth hiring.
Stage 1: Site visit and layout (day 1)
We walk the property line with you, confirm where the fence will sit, and mark posts with stakes. If your line needs verification, we recommend a surveyor. You’ll decide the fence style, color, and gate locations on this visit. This typically takes 1 to 2 hours on a healthy lot.
Stage 2: Permitting and utility locate (days 1-14, often the slowest step)
Because South Whittier is unincorporated LA County, fence permits go through LA County Public Works, not a city building department. For most residential iron fences under 6 feet tall, no permit is required, but anything taller, near a corner, or on a slope may trigger one. We call 811 for utility locates regardless. You’ll decide during this stage whether to proceed without a permit (most do) or wait it out.
Stage 3: Demolition and post footings (days 2-3)
We pull the old fence, dig post holes to 24 to 36 inches deep depending on soil and fence height, and set posts in concrete. Footings cure 24 to 48 hours before we hang anything. You’ll decide at this stage whether to keep the old fence for a day or two of overlap for pets, or go without.
Stage 4: Panel hang and gate install (days 3-5)
Rails go up, pickets get spaced, and gates get hung on hinges with proper swing clearance. This is where an iron fence either looks tight or looks cheap. Expect 2 to 3 days on a typical 120-foot run.
Stage 5: Finish and touch-up (day 5-6)
We touch up weld points and any scratched paint with matching enamel, then walk the fence with you line by line. If anything is off, we fix it on the spot. Workmanship is covered by our 730-Day Done Right Promise, so if something rusts or loosens within two years, we come back.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Iron Fence Options You’ll Actually Be Choosing Between
Iron fence is a loose term. What you’re really picking is a metal type, an assembly style, and a finish. Here’s the honest breakdown.
- Wrought iron (traditional): Hand-forged or traditional-style solid bars, heavier gauge, welded or riveted. Top of the price range, $70 to $120 per linear foot. Best look, longest life, but requires repainting every 5 to 8 years.
- Steel or tubular steel: Cheaper ($45 to $75 per foot), often the practical pick for South Whittier backyards. Painted black, indistinguishable from wrought iron at 10 feet.
- Aluminum “iron-style”: Looks similar, never rusts, but dentable and lighter. Not our first choice for front-yard security, but a smart pick near the pool area or for interior property divisions.
- Powder coat vs. wet paint finish: Powder coat costs more up front but holds up 3 to 5 years longer in hot, dry conditions.
- Picket spacing and height: 4-inch spacing for pool code, tighter for pets, wider for view. Height drives both cost and, above 6 feet, whether LA County wants a permit.
Homeowners often pair this with Patios, Walkways & Pool Decks in South Whittier when the fence defines a new outdoor living area, or as part of a full Fence Installation in South Whittier scope that includes gates and side-yard dividers.
What Iron Fence Costs in South Whittier, CA

The full project lands in the $3,500 to $9,000 range for a standard residential job. Here’s what moves the number up or down:
| Factor | Low end | High end |
|---|---|---|
| Linear feet (100 → 200) | $3,500 | $9,000 |
| Height (4 ft → 7 ft) | +$0 | +$2,500 |
| Gates (1 walk gate → 2 + driveway) | +$400 | +$2,800 |
| Material (steel → wrought iron) | $0 | +$3,000 |
| Demo and haul-off of old fence | +$300 | +$900 |
What’s included in our written estimate: demo and haul-off, footings and concrete, fence panels, gates with hardware, powder or wet-coat finish, touch-up, and cleanup. What typically isn’t: surveying, retaining walls behind the fence line, landscaping repair after install, and any electrical work for an automatic driveway gate. If your iron fence lines a new ADU lot line, coordinate with whoever is handling your ADU Design & Permitting in South Whittier, because the survey runs are usually shared.
We offer up-front pricing so the number you see on the estimate is the number you pay. Promotions on larger projects ($1,000 off projects over $10,000, 0% financing for 18 months) apply if the fence is bundled into a wider scope.
See the difference
Before
After
Before
After
Before
AfterWhat South Whittier Homes Specifically Do to This Iron Fence Job
This is an unincorporated pocket of LA County, and the permitting reality is different from neighbors like Whittier or Santa Fe Springs. Plans and fence permits route through LA County Public Works, and inspection scheduling runs on their calendar, not a municipal one. That changes timing more than it changes the fence itself. On older lots off streets like Telegraph Road and the quiet blocks feeding into the 90605 ZIP, we routinely find 1940s and 1950s single-story stucco homes on 6,000 to 8,000 square foot lots with detached garages and property lines drawn decades ago. When fences sit on those old lot lines, they’re often 6 to 18 inches off from what the plat map shows. We flag that on day one, because installing 150 feet of iron on a wrong line is expensive to undo. The dry summers and Santa Ana wind gusts also matter: powder coat and heavier-gauge steel hold up better than wet paint over 10 to 15 years, and gate latches should be wind-rated, not the cheap gravity latches. Covering all of South Whittier is routine for our crews, and our fence installation service follows the same up-front pricing and background-checked, uniformed technician policy on every job.
Serving South Whittier, CA – Our Local Coverage Area
We serve South Whittier and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions: Iron Fence in South Whittier

Most iron fences in South Whittier are finished in 4 to 6 working days from the start of demo. The permit and utility locate window (if needed) can add 1 to 3 weeks. Call (888) 255-8179 for an exact timeline on your property.
Usually not. Residential iron fences up to 6 feet tall on interior lot lines typically don’t require a LA County permit, though corner lots, slopes, and anything over 6 feet often do. We file on your behalf when one is needed, and the fee is itemized in the estimate.
Yes, and we do it on most jobs. We dig individual post holes rather than trenching, so grass and landscaping recovery is fast. Irrigation lines get flagged during the utility locate or hand-probed before digging so nothing gets punctured. Call (888) 255-8179 to schedule a site walk before we finalize anything.
Plan on $3,500 to $9,000 for most residential South Whittier iron fence jobs, with the spread driven by linear footage, height, gate count, and material. Estimates are free and itemized; call (888) 255-8179 to book one.
Our workmanship is backed by the 730-Day Done Right Promise. If a weld fails, a post loosens, or a gate sags within that window, we come back and make it right. Material warranties vary by manufacturer and are documented in your written estimate.
Get a Free Iron Fence Estimate in South Whittier
Tell us roughly how many feet of fence you need and where the line runs. We’ll come out, walk it with you, and hand you a written line-item estimate the same visit. You’ll get straight answers on permit need, gate placement, and material fit for your lot. Prices are up front, and the number you see is the number you pay. Call (888) 255-8179 to get on the schedule.
Written by the team at Groundwork Construction Co.












