







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Metal Roofing in Pico Rivera, CA: What It Costs and How Long It Takes
Metal roofing in Pico Rivera runs $15,000 to $40,000 for most homes, with a typical 1,400-square-foot 1950s tract house landing near the lower half of that range. The job itself takes three to seven working days from tear-off to final inspection, and most of that clock is spent on deck prep and trim, not on laying panels. Call (888) 255-8179 for a free on-site estimate with a written line-item quote.
How a Metal Roof Goes On: Day by Day

Metal is not a same-shape swap with asphalt shingles. The subfloor, the underlayment and the trim all change, and the sequence matters more than the material list. Here is how we run it.
Day 1: Tear-off and deck inspection
We strip the existing roof down to the sheathing, on a 1,200 to 1,600 square-foot Pico Rivera house usually in a single day. Then we inspect the deck board by board. On homes from the 1950s and 60s, we routinely find soft spots near valleys and penetrations from decades of Santa Ana wind-driven dust and winter rain. You’ll see the estimate for any deck replacement before we touch it.
Day 2: Repair, re-nail, and underlayment
Bad sheathing comes out, the deck gets re-nailed to current fastener spacing, and we roll out a high-temp synthetic underlayment rated for metal. This is also when ice-and-water-style membrane goes in the valleys and along the eaves. You don’t have a decision to make here unless the deck damage turns out worse than the inspection showed. If it does, we stop and show you photos before adding cost.
Days 3 to 5: Trim, panels, and fastening
Eave trim, rake trim and any valley flashing go on first, then the panels or shingles, then the ridge cap. This is the longest stretch, and it’s where a low bid shows up. Panel spacing, overlap and the concealed fastener pattern determine whether the roof sheds water for thirty years or leaks at year six. You’ll want to decide up front between panel profiles, and that choice gets locked in before day one.
Day 5 to 6: Penetrations and flashing
Vents, chimney flashing, and any skylight curbs get sealed last, after the field is done. This is the trim work that separates a good metal roof from an average one. On Pico Rivera houses, the number of penetrations is usually modest, but older vent stacks are often out of plumb and need custom boots rather than standard ones.
Day 6 to 7: Final inspection and cleanup
We walk the roof, run a magnet over the yard for stray fasteners, and coordinate the final inspection with the city. You get the inspection sign-off and the material warranty paperwork at the walkthrough. Most metal roof jobs on a Pico Rivera tract home finish inside that window. Larger homes with complex hips and valleys stretch to the far end.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Your Options: Panels, Shingles, and Finishes
The choices below are the real decision points a buyer sits with. Each one trades cost against lifespan, appearance, and how much the installer has to deviate from a standard install.
- Standing seam panels (the premium route). Concealed fasteners, raised seams, cleanest look, and the longest service life. Costs more per square foot and requires a fabricator and a crew that knows the profile. Suits a homeowner planning to stay in the house decades and paying attention to curb appeal.
- Corrugated or exposed-fastener panels. The budget end of the metal category. Fastener washers are the weak point over time, so this option makes sense when the budget is tight and the roofline is simple. Expect a shorter lifespan than standing seam.
- Metal shingles and stamped tiles. Metal stamped to mimic the barrel tile or shake look that matches Pico Rivera’s mixed rooflines. Middle price band. Gives you metal’s durability without the industrial look on a Spanish-style front elevation.
- Paint finish and color. The factory finish determines fade resistance under the inland sun. A quality finish with a long warranty costs more than a basic one. You can see the difference in a decade on a south-facing plane.
- Underlayment and deck upgrades. The materials that rarely show on a bid. A high-temp synthetic underlayment and new sheathing where needed are what let the metal last its rated life. You’ll usually see Southwestern roofs skip this. We don’t.
What Metal Roofing Costs in Pico Rivera, CA

Here is the line-item range we work to, calibrated to Pico Rivera’s tract-home stock.
| Scope | Typical Range |
|---|---|
| Full metal roof installation (1,200 – 2,000 sq. ft.) | $15,000 – $40,000 |
| Roof replacement, comparable scope | $8,000 – $20,000 |
| Roof repair for isolated issues | $400 – $1,800 |
| Tile roof repair (if replacing a tile section) | $600 – $2,500 |
What pushes a job to the low or high end
Four things drive the spread. First, roof size and complexity: a simple gable on 1,200 square feet sits at the low end, while a hip-and-valley roof on 2,000 square feet pushes past $30,000. Second, existing deck condition: soft sheathing from decades of heat and rain cycles adds cost, and we only add what’s needed. Third, material grade: standing seam runs higher than exposed-fastener panels, and stamped tile sits between. Fourth, permit scope: if the job touches structure or adds a skylight, the inspection set grows and the permit cost with it.
What a written estimate includes and doesn’t
Our written estimate includes tear-off and disposal, deck inspection and repair line items, underlayment, trim, fasteners, flashing, permits, and the final inspection. It does not include structural remediation if a rot inspection reveals framing damage, and it does not include skylight hardware. Those get quoted separately and only after you see the finding. The number on the estimate is the number you pay for the scope we agreed to, with no change orders without your sign-off.
See the difference
Before
After
Before
After
Before
AfterWhat Pico Rivera Homes Specifically Do to This Job
Pico Rivera is a built-out, post-war working-class suburb, and most of its single-family homes went up in the 1950s and 60s. That means we’re rarely roofing a fresh build. We’re re-roofing a house that’s already been through sixty summers of inland heat and a handful of dry Santa Ana wind events that pry at eaves and ridge caps. On these tracts, the sheathing is often original, the bajo sloped, and the chimney flashing has been patched more than once. The winter rain exposes what the summer baked, and we see active leaks show up in January on roofs that looked fine in September. Most of our metal roofing work here is owner-occupied, families who plan to stay, so the question isn’t “what’s the cheapest thing that works” but “what lasts.”
If the metal roof is part of a larger exterior project, it fits with Roofing in Pico Rivera and can be phased alongside Window Replacement in Pico Rivera if the windows are also due. If the home is a garage conversion or addition, the metal roof often ties into a new addition. Energy-efficient options pair well with Impact Windows & Doors in Pico Rivera. For the wider picture of our Roofing services across the region, the service hub covers it. And if you’re evaluating coverage in Pico Rivera or the surrounding ZIP codes 90660, 90661, and 90662, we serve the full area.
Serving Pico Rivera, CA – Our Local Coverage Area
We serve Pico Rivera and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Metal Roofing in Pico Rivera

Most jobs run three to seven working days, with single-story tract homes on the short end and complex rooflines on the long end. Your start date depends on permit turnaround with the city and on material lead time for a custom panel profile. Call (888) 255-8179 to talk through timing for your house; estimates are free.
Yes, a re-roof permit is required, and any structural changes or added penetrations raise the scope of the inspection. The city inspects the deck and the final roof, and that sign-off belongs in your file. We pull the permit and schedule the inspections for you. For an exact scope the number is (888) 255-8179.
Usually, yes. Standing seam and metal shingles are engineered for standard residential framing, so in most Pico Rivera homes no structural changes are needed. If the deck is soft or out of square, we repair the sheathing first, but that’s still not a framing change. We’ll tell you at the on-site estimate what your house actually needs.
The range is $15,000 to $40,000 for most single-family homes in the city, with the typical 1950s – 60s tract house landing near the lower half. Standing seam runs at the high end, exposed-fastener panels at the low end, and stamped metal shingles sit between. Call (888) 255-8179 for a free estimate with line-item pricing.
You get two warranties: the manufacturer’s material warranty on the panels and finish, and our 730-Day Done Right Promise on the workmanship. If anything we installed fails within that window, we make it right, and that’s in writing. Call (888) 255-8179 to schedule your free estimate.
Get a Free Metal Roofing Estimate in Pico Rivera
We’ll come out, measure the roof, inspect the deck and sheathing, and walk you through exactly what the job needs and what it doesn’t. You’ll get a written line-item quote, an honest timeline, and a real answer on the material choices before you commit to anything. Call (888) 255-8179 to schedule your free estimate. A live person answers around the clock, every day of the week.
Written by the team at Groundwork Construction Co.












