







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tub-to-Shower Conversion in Whittier, CA: What It Involves and What It Costs
A tub-to-shower conversion in Whittier runs $3,500 to $10,000 and takes five to ten working days from demo to final inspection. The job means pulling the old tub and its surround, reworking the drain and valve to shower height, waterproofing the wet zone, then setting a new pan, tile, and glass. Most Whittier homeowners land in the $5,500 to $7,500 band when the plumbing stays put and the tile is a mid-grade porcelain. Call (888) 255-8179 for a free on-site estimate.
How Our Tub-to-Shower Conversion Process Actually Runs

We don’t hand you a start date and disappear. Here’s the sequence we follow on a Whittier tub-to-shower conversion, with the decisions you’ll make at each stage.
Stage 1: Demo and inspection (days 1 – 2)
The tub, surround, and any furring come out. We open the wall around the valve to see what’s behind it. On 1950s Whittier ranches, that’s often galvanized supply lines near the end of their life or a valve set for a tub spout rather than a shower arm. You decide then whether to replace the valve now or keep it. Replacing it mid-conversion adds $400 to $900 but saves tearing the wall open again in three years.
Stage 2: Rough-in and framing (days 2 – 3)
The drain gets moved to the new pan location, the shower valve is set at proper height, and we block the walls for grab bars and a bench if you want one. This is where the price can move. If the drain sits directly under the tub, relocation is minor. If it’s offset or the floor is slab-on-grade, we’re cutting concrete, and that’s a line item.
Stage 3: Waterproofing (day 3 – 4)
We install a bonded waterproofing membrane over cement board, seal every seam and corner, and flood-test the pan. This is the stage most cheap conversions skip, and it’s the one that decides whether the Whittier home has a mold problem in five years. No membrane, no warranty from us. Full stop.
Stage 4: Tile and fixtures (days 4 – 7)
Wall tile, floor tile, niche, and trim go in. You’ve already picked the tile at the estimate stage; this is where sizing and layout get finalized. Kohler or Moen fixtures are set once the tile cures. Grout and caulk come last, and we let the shower sit a full day before any water hits it.
Stage 5: Glass, inspection, and walkthrough (days 8 – 10)
Glass goes in, the permit inspection happens, and we walk you through the finished shower. You get the 730-Day Done Right Promise in writing at that walkthrough. If a tile cracks or a seal fails in that window, we come back and fix it, no argument.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
Most of the decisions on a Whittier tub-to-shower conversion fall into five buckets. Here’s what each one really costs you in money and time.
- Shower pan: A pre-formed acrylic pan runs $300 to $700 installed and is fast, but it limits you to standard sizes. A custom mud-set tile pan runs $900 to $1,800 and lets you fit any footprint, including the odd 30-by-60 alcove you’ll find in older Whittier homes. We recommend tile if the floor is out of level.
- Wall finish: Porcelain or ceramic tile starts around $8 to $15 per square foot installed. Large-format slabs look cleaner with fewer grout lines but cost $20 to $40 per square foot and require a perfectly flat substrate. Cultured marble panels sit in the middle: $1,200 to $2,500 total, low maintenance, but they read dated in ten years.
- Fixtures: Delta and Moen make reliable valve-and-trim sets at $250 to $600. Kohler runs $500 to $1,200 for the same function with a better finish and warranty. The valve is the part you can’t easily replace later, so we push clients to spend there.
- Glass: A framed sliding door runs $600 to $1,200. A frameless glass panel or door runs $1,400 to $2,800. Frameless looks better and is easier to clean, but the wall has to be square, which matters on homes built before 1960.
- Accessories: A built-in bench adds $400 to $900. A niche adds $150 to $350. Grab bar blocking is free if we know at framing stage and $300-plus if we have to open a finished wall later.
What Tub-to-Shower Conversion Costs in Whittier, CA

Expect $3,500 to $10,000 for a tub-to-shower conversion in Whittier, with the median job landing near $6,200. Five things move that number, and we tell you which ones apply before you sign anything.
- Size and layout: A standard 30-by-60 alcove conversion is the cheapest. A 48-by-60 or a walk-in with a bench pushes into the $8,000 to $10,000 range.
- Existing condition: Galvanized supply lines, cast-iron drains, or a rotted subfloor discovered at demo add $800 to $2,500. We flag likely risks at the estimate so nothing surprises you mid-job.
- Moving plumbing, electrical, or structure: Relocating the drain in a slab floor adds $600 to $1,500. Moving a wall or adding a curbless entry can add $1,500 to $3,000. If you want a curbless shower on a wood subfloor, the whole floor assembly has to be reworked.
- Material grade: A basic ceramic-and-acrylic conversion sits at the low end. Porcelain, frameless glass, and Kohler trim push toward the top. The finish line alone can swing $1,500.
- Permit scope: A straight fixture swap may not require a permit in every jurisdiction; moving the drain or valve generally does. We pull what’s required and factor the fee into the written estimate, so you’re not chasing a surprise invoice later.
Our written estimate lists every line item: demo, rough-in, waterproofing, tile, fixtures, glass, permit, and labor. The number you see is the number you pay. If you decide to expand the job into a Bathroom Remodeling in Whittier that touches the vanity, lighting, and floor, that’s a separate scope and a separate estimate, but we’ll price both so you can compare side by side.
See the difference
Before
After
Before
After
Before
AfterWhat Whittier Homes Specifically Do to This Job
Whittier has two very different housing realities, and a tub-to-shower conversion runs differently in each. In the Uptown core around 90601, the housing stock is largely 1910s-to-1950s Craftsman and Spanish Colonial Revival, and much of it sits inside a state-designated historic overlay. That means a conversion that changes the exterior window or a wall configuration can trigger a design-review permit, adding two to four weeks to the schedule. It also means the plumbing inside those walls is often original cast iron and galvanized steel, which we plan to inspect at demo.
Across the eastern ZIPs (90604, 90606, 90612), the housing is mid-century ranch tracts on slab-on-grade, built roughly 1950 to 1968. The tub alcoves are usually standard 30-by-60, which saves money on a conversion, but the same homes often have undersized electrical panels and original copper or galvanized supply lines that fail a straight feel test. Water here is hard enough that shower valves and cartridges need replacement sooner than most homeowners expect; we see seized cartridges constantly on showers older than fifteen years.
And the semi-arid basin climate at the foot of the Puente Hills plays a role inside the shower too. Dry summers and Santa Ana wind episodes pull moisture out of wall assemblies, and tile that was set without proper backer or membrane will show hairline cracks within a few seasons. We use cement board and bonded membrane on every conversion in Whittier, no exceptions. If you’re also handling the roof on the same project, homeowners often pair this with Tile Roofing in Whittier or Metal Roofing in Whittier to get the exterior work done in one planning cycle.
Serving Whittier, CA – Our Local Coverage Area
We serve Whittier and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Tub-to-Shower Conversion in Whittier

A typical conversion takes five to ten working days from demo to final walkthrough. Straight alcove swaps with in-stock tile land near the five-day mark; custom tile, glass, and any plumbing relocation push toward ten. A historic-overlay permit on an Uptown home can add two to four weeks to the front-end schedule. Call (888) 255-8179 and we’ll give you a realistic date range for your specific address.
Usually yes if the drain or valve is being moved, and sometimes not if it’s a straight fixture-and-tile swap in the same footprint. The only way to know for your address is to check with the city, and we handle that for you as part of the written estimate. Pulling the permit protects you at resale and gets you an inspection record for the plumbing. Call us to talk through your specific scope before you commit to a plan.
Yes, and that’s the most common job we do. If the drain sits directly under the tub and the valve is already at shower height, the conversion stays in the same footprint and the price stays at the low end of the $3,500 to $10,000 range. Moving the drain in a slab floor or changing a wall is what pushes the number up. Call for an on-site look and we’ll tell you straight whether the plumbing needs to move.
The range is $3,500 to $10,000, with most Whittier jobs landing around $6,200. The variables are size, existing plumbing condition, whether the drain moves, tile and fixture grade, and permit scope. A written line-item estimate takes the guesswork out. Call (888) 255-8179 for a free quote, and ask about the $1,000 off projects over $10,000 if you’re also touching the vanity or floor.
Every conversion we complete is covered by our 730-Day Done Right Promise: if anything we installed fails within that window, we come back and make it right at no charge. Waterproofing failures and tile failures are both covered. We don’t shorten the warranty for tile work or for the plumbing rough-in. Call (888) 255-8179 and we’ll send the warranty terms in writing before you sign anything.
Get a Free On-Site Estimate for Your Whittier Tub-to-Shower Conversion
Call (888) 255-8179 for a free estimate on your tub-to-shower conversion in Whittier. A live person answers around the clock, not a voicemail box. We’ll schedule an on-site walkthrough, measure the alcove, inspect the plumbing, and hand you a written line-item quote with the permit scope and timeline spelled out. No pressure, no sales pitch, just the number and the plan. You can see the full scope of our Bathroom Remodeling work and the areas we cover, including Whittier and the surrounding neighborhoods.
Written by the team at Groundwork Construction Co.












