







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Vanities, Tile & Fixtures in Santa Fe Springs: What It Really Takes
Replacing a vanity, retiling a floor or shower surround, and swapping out fixtures in a Santa Fe Springs bathroom usually runs $9,000 – $28,000 for a full tear-out and rebuild, or $800 – $3,000 if you’re only setting a new vanity. Most jobs take two to four weeks once materials are on site. Vanities, Tile & Fixtures work is the part of a bathroom that shows every day, so the spec choices matter as much as the labor. Call (888) 255-8179 to schedule a free on-site estimate.
How We Sequence Vanities, Tile & Fixtures Work

We don’t hand a bathroom over to a tile setter and hope the plumber shows up. The order matters, and skipping a step costs you a redo.
Day 1: Demo and discovery
We pull the vanity, toilet, and old tile down to the studs and subfloor. This is where surprises show up: a rotted sill plate behind a 1950s tub wall, galvanized supply lines that crumble when touched, or a floor that was never leveled. We photograph everything and walk you through what we found before we start putting things back. If the discovery changes scope, you hear about it that day, not three weeks later.
Days 2 – 3: Rough-in and prep
Any plumbing relocation, new valve, or added GFCI outlet happens now, before a single tile goes down. We set a cement backer board or a waterproof membrane system on the wet walls, tape and seal the seams, and let the pan or receptor cure. This stage is unglamorous and invisible in the finished room, which is exactly why we don’t rush it. You’ll confirm the fixture locations and drain position here.
Days 4 – 8: Tile setting
Floor tile first, then walls. Large-format porcelain takes longer to set than 4-inch ceramic because each piece has to be flat and level across a wider span; a small bathroom floor in Santa Fe Springs typically takes a day and a half to lay and another day before grouting. We grout last so the wall grout doesn’t get walked on while it cures.
Days 9 – 12: Vanity, top, and fixtures
The vanity cabinet goes against the wall, shimmed and anchored, then the countertop and undermount sink. Faucet, drain, supply lines, and the P-trap connect after. Toilet reset or replacement closes out this stage. You’ll want to have your fixtures chosen and delivered before this day; the cabinet and top can’t be final-set without them.
Days 13 – 14: Final trim, caulk, and walkthrough
Mirror, towel bars, door hardware, and the last bit of caulk at the tub or shower seam. We run water, check for leaks under the sink, test the drain, and walk the room with you under our 730-Day Done Right Promise. If a tile is lipping or a grout line is off, we fix it before we call it done.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
Most of the time a Santa Fe Springs homeowner is picking from the same set of choices. Here’s the honest trade-off on each.
- Vanity cabinet material: plywood box with a furniture finish holds up to moisture far better than particleboard, though it costs 30 – 40% more. Particleboard is fine in a low-use powder room but swells around a shower.
- Vanity top: quartz is the practical pick for a wet room; it resists stains and doesn’t need sealing. Natural stone looks richer but wants annual sealing. Cultured marble is the value option at the low end.
- Tile type for the floor: porcelain is dense, water-resistant, and forgiving of a slightly uneven subfloor. Ceramic is cheaper but chips more easily. Natural stone tile (travertine, slate) needs a stiffer subfloor and sealing, and we’ll tell you if the existing floor won’t carry it.
- Shower wall material: large-format porcelain or a waterproof board system keeps grout lines few; a traditional tile-and-grout wall needs resealing over time. We’ll show both installed examples.
- Fixtures: a Kohler or Moen faucet with a ceramic cartridge outlasts an off-brand unit several times over. The valve inside the wall is the part you can’t easily replace later, so we don’t cheap out there.
- Tile size: 12×24 is easier to clean and fewer grout lines; 3-inch hex on the floor gives more slip resistance and a period look for a mid-century ranch.
What Vanities, Tile & Fixtures Costs in Santa Fe Springs, CA

For a full bathroom tile, vanity, and fixture replacement in Santa Fe Springs, plan on $9,000 – $28,000. A vanity-only install runs $800 – $3,000, a shower replacement $3,000 – $8,500, and a walk-in shower conversion $4,500 – $12,000. Here’s what pushes the number to one end or the other.
| Line item | Typical range in Santa Fe Springs |
|---|---|
| Vanity install (cabinet, top, sink) | $800 – $3,000 |
| Shower replacement | $3,000 – $8,500 |
| Walk-in shower installation | $4,500 – $12,000 |
| Full bath: tile, vanity, fixtures | $9,000 – $28,000 |
What moves the price:
- Existing condition. A war-era ranch with a rotted subfloor or galvanized plumbing adds demo and repair time.
- Plumbing or electrical relocation. Moving a drain or adding a GFCI outlet means opening walls and pulling a permit.
- Material grade. Porcelain and quartz sit in the middle; natural stone and custom cabinetry push to the high end.
- Bathroom size. A small hall bath finishes closer to $9,000; a full-size primary bath lands near $28,000.
- Permit and inspection scope. Any structural or plumbing change requires a city permit and an inspection.
What’s included in a written estimate: demo, rough-in, waterproofing, tile, vanity set, fixtures connect, and final walkthrough. What’s not: the cabinet and fixtures themselves unless you ask us to source them, and any concealed rot or plumbing we can’t see until demo. We put the allowance in writing so you know before we start. The number you see is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhy Santa Fe Springs Addresses Make This Job Different
Santa Fe Springs is an industrial and commercial job site with homes tucked alongside it. The 1940s – 70s ranches sit immediately next to warehouses and truck yards off the 5 and 605, and the older residential pockets are exactly where vanities, tile, and fixture work turns into a bigger job than the homeowner expected.
Most of the housing here was built between the late 1940s and the 1970s. In those homes, we regularly find original galvanized supply lines that won’t survive a vanity demo, undersized electrical panels that can’t carry a new GFCI or heated mirror, and subfloors that were never meant to hold stone tile. A 1950s ranch bath gone to the studs is a different repair than a 2000s build. The hot inland summers and Santa Ana winds off the Whittier Narrows also dry out grout and caulk seams faster than coastal homes, so we spec a flexible sealant at the tub and shower joints and check drainage at the pan to avoid the mold we see in bathrooms that never got a proper slope.
Because this is Santa Fe Springs and the city stays on top of both industrial and residential permits, any plumbing or structural change gets pulled and inspected. We cover the 90670 and 90671 ZIPs and the neighboring pockets toward Downey, Pico Rivera, and South Whittier. If your vanities, tile, and fixtures are part of a larger scope, we handle that under our Bathroom Remodeling in Santa Fe Springs. And if the same older roof is on your list, homeowners often pair this with Tile Roofing in Santa Fe Springs or Specialty Roofing in Santa Fe Springs while the scaffolding is up. Our Santa Fe Springs service page lists everything we do here.
Serving Santa Fe Springs, CA – Our Local Coverage Area
We serve Santa Fe Springs and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Vanities, Tile & Fixtures in Santa Fe Springs

Most jobs take two to four weeks from demo to walkthrough, with the tile-and-grout stage taking up the biggest share. A vanity-only swap can finish in a day. Call (888) 255-8179 for a timeline tied to your bathroom.
You need a permit if the work touches plumbing, electrical, or structure; a cosmetic tile or vanity swap on the same footprint usually does not. We tell you which applies before we start and pull what’s required for you.
Yes. If the existing drain and supply lines are sound, we set the new vanity on the same rough-in and swap the fixtures without opening walls. That keeps the job leaner. If the lines are galvanized and failing, we’ll show you why a relocation or repipe is worth it.
Vanity installation runs $800 – $3,000, a full bathroom tile, vanity, and fixture package runs $9,000 – $28,000, and a shower replacement runs $3,000 – $8,500. Call (888) 255-8179 for an exact quote; estimates are free.
Every job is backed by our 730-Day Done Right Promise, one of the longest workmanship guarantees in the residential construction space. If a tile pops, a seam leaks, or a fixture misbehaves, we make it right.
Get a Free Estimate on Vanities, Tile & Fixtures
Call (888) 255-8179 to book a free on-site estimate for vanities, tile, and fixtures in Santa Fe Springs. A live person answers around the clock. We’ll measure the room, walk the existing plumbing and subfloor, and hand you a written line-item quote with material pricing and a real timeline. No pressure and no change orders once work starts. Groundwork Construction Co. of Downey also offers $1,000 off projects over $10,000 and 0% financing for 18 months. See our Bathroom Remodeling service for the full picture.
Written by the team at Groundwork Construction Co.












