







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tub-to-Shower Conversion in Santa Fe Springs, CA: What It Costs and How Long It Takes
A tub-to-shower conversion in Santa Fe Springs typically runs $3,500 to $10,000 and takes 3 to 7 working days once demolition starts, depending on whether we’re relocating the drain and valve or reusing what’s there. The job means pulling the old tub and its surround, prepping the walls and pan, setting a new waterproofed shower base and tile, and connecting new fixtures. To price your specific bathroom, call (888) 255-8179 and we’ll set up a free on-site estimate.
How We Run a Tub-to-Shower Conversion, Stage by Stage

This isn’t a one-day swap. A proper conversion involves waterproofing, a permit, and an inspection, and skipping any of those stages is how showers fail two winters later. Here’s the real sequence and where you make decisions.
Stage 1: Measure, inspect, and lock the layout (day 1, about 90 minutes)
We pull the tub surround and look behind the wall before quoting the final number, because Santa Fe Springs homes built from the late 1940s into the 1970s often hide galvanized supply lines and a valve that’s been patched once already. You decide the shower footprint (30×60 or 36×60 are the two standards that fit a tub alcove) and whether the drain stays centered where it is. Reusing the existing drain location is the single biggest cost saver on this job.
Stage 2: Permits and demo (days 1 and 2)
We file the plumbing and building permit with the city and schedule the rough-in inspection. Demo runs a half day: tub out, old cement board and any water-damaged framing removed, debris hauled. If we find rot in the subfloor or studs behind the wet wall, you get a written change order before we touch anything else. No surprise line items after the fact.
Stage 3: Rough plumbing and inspection (day 2, then a wait for the inspector)
New valve, new drain and trap as needed, then the rough-in inspection. Santa Fe Springs runs a steady inspection calendar, so plan on one to three business days for the inspector to sign off before we close the walls. This is the stage homeowners underestimate. You decide the valve trim here, and we recommend a pressure-balance or thermostatic valve rather than a two-handle unit, since the inland heat means people shower at higher temps and a scald guard earns its keep.
Stage 4: Waterproofing and tile (days 3 through 5)
Cement board, a bonded waterproof membrane on the pan and walls, then tile or a solid-surface panel. Waterproofing is the part nobody sees and the part that decides whether this shower lasts. We flood-test the pan for 24 hours before setting a single tile. You’ll pick tile size, grout, and whether you want a niche, bench, or grab bar blocking installed now (far cheaper than retrofitting later).
Stage 5: Set, grout, glass, final inspection (days 6 and 7)
Fixtures go on, glass gets templated and installed, and the city does the final inspection. We walk you through caulk lines, drain maintenance, and how to care for the tile. Most jobs finish inside a week of demo; a plumbing relocation or a surprise rotted subfloor can push it to ten days.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between (and What Each One Costs You)
The material and configuration choices are where a $3,500 conversion becomes a $10,000 one. Here’s the honest trade-off on each.
- Acrylic or fiberglass shower surround: The budget choice, roughly $1,800 to $3,500 installed. Goes in fast, cleans easily, and suits a rental or a bathroom you’re not planning to stay in. Trade-off: it looks like a kit, and the seams can stain over a decade.
- Ceramic or porcelain tile over a waterproofed pan: The standard for a reason, about $4,000 to $8,000 depending on tile and layout. Durable, resists the hard water we see around the Whittier Narrows, and lets you match the rest of the house. Trade-off: grout needs sealing, and a poor waterproofing job behind it is invisible until it fails.
- Large-format porcelain panels: Fewer grout lines, a clean modern look, $6,000 to $10,000. Trade-off: needs a skilled setter and precise wall prep, so the labor is the cost, not the material.
- Valve and trim: A basic pressure-balance valve from Delta or Moen runs $150 to $400 in parts; a thermostatic setup with a rain head pushes toward $800 to $1,500. Both hold up; the upgrade buys temperature control, not durability.
- Glass enclosure: Frameless glass runs $900 to $2,000 and defines the look. A framed slider is $400 to $800 and easier to keep aligned. Skip glass entirely and use a curtain if budget is the priority.
- Bench, niche, and grab bar blocking: Add $300 to $1,200 together. Do this during framing, not after. Retrofitting a grab bar into finished tile later means drilling through waterproofing.
If you’re weighing the shower against a wider refresh, this work often becomes part of a full Bathroom Remodeling in Santa Fe Springs once the walls are open anyway.
What Tub-to-Shower Conversion Costs in Santa Fe Springs, CA

Expect $3,500 to $10,000 for the conversion, with most Santa Fe Springs jobs landing between $5,000 and $7,500. That range reflects real variables, not a guess.
| Line item | Typical range |
|---|---|
| Tub removal, demo, and haul-away | $400 – $900 |
| Shower pan, waterproofing, and tile | $1,800 – $4,500 |
| Rough plumbing and new valve | $600 – $1,800 |
| Glass enclosure | $400 – $2,000 |
| Permit and inspection fees | $250 – $700 |
| Fixture trim (head, handle, drain) | $150 – $800 |
What pushes a job toward the high end: relocating the drain or valve (add $800 to $2,000), a rotted subfloor or studs (add $500 to $1,500), large-format tile needing extra wall prep, and a bench or niche added mid-project. What keeps it low: reusing the existing drain location, a stock acrylic surround, and a straightforward demo with no rot behind the wall.
Our estimate is written line by line, so you see the permit line, the tile line, and the fixture line before we start. Upfront pricing, no surprises means the number you approve is the number you pay, unless you change the scope in writing. If you’d rather browse the full picture, see our Bathroom Remodeling service.
See the difference
Before
After
Before
After
Before
AfterWhat Santa Fe Springs Homes Specifically Do to This Job
Santa Fe Springs is an industrial city with homes tucked alongside it, and that shapes what we find behind the wall. The tract houses here went up between the late 1940s and the 1970s, so a 1950s ranch near the 605 will often have original galvanized supply lines feeding the tub valve, and swapping to a shower means we may need to address that supply run while the wall is open. Undersized electrical panels show up too, especially when a homeowner wants a light and exhaust fan added where the tub used to be. Because these are war-era and mid-century homes, the framing isn’t always square, and we plan tile layout around that instead of pretending it is.
The permitting side matters here more than in most of the region. Santa Fe Springs runs its own inspection and permitting process, and the city’s planning and design review culture is strict, so a bathroom permit needs a clean drawing set and a realistic inspection window. We file it correctly the first time and schedule the rough-in and final inspections, so you don’t spend three weeks waiting on a re-submittal. Homes in the 90670 ZIP near the rail yards also deal with a dusty, truck-traffic-heavy environment, and that dust finds its way into a bathroom during demo. We contain the work area. If you’re also planning exterior work, homeowners often pair this with Metal Roofing in Santa Fe Springs to handle the sun and wind exposure the inland climate throws at these older roofs.
As a comprehensive guide to the area, our Santa Fe Springs page explains exactly what we handle here. If the roof needs attention before the interior work, we also do Tile Roofing in Santa Fe Springs. Our technicians have up to 12 years of experience, and every project carries our 730-Day Done Right Promise.
Serving Santa Fe Springs, CA – Our Local Coverage Area
We serve Santa Fe Springs and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Tub-to-Shower Conversion in Santa Fe Springs

Plan on 3 to 7 working days of active work, plus one to three business days waiting on the city’s rough-in inspection. Jobs that relocate the drain or find rotted framing run closer to ten days. Call (888) 255-8179 and we’ll give you a dated schedule with your estimate.
Yes, in most cases. Changing a tub to a shower alters the plumbing rough-in and creates a new wet-area waterproofing condition, and Santa Fe Springs requires a permit and at least a rough-in plus final inspection for that work. We pull the permit and pass the inspection as part of the project.
Usually, yes. If your existing drain sits within the standard 30×60 or 36×60 shower footprint, we reuse it and the valve location, which keeps the job in the $3,500 to $6,000 range. Moving the drain to a new spot or relocating the valve adds $800 to $2,000. We confirm this on site before quoting.
It runs $3,500 to $10,000, with most jobs between $5,000 and $7,500 once you factor in permit, waterproofing, tile, and glass. Acrylic surrounds land low, and large-format tile with frameless glass and a bench lands high. Call (888) 255-8179 for an exact line-item quote on your bathroom; estimates are free.
Every conversion is covered by our 730-Day Done Right Promise: if it isn’t done right, we make it right. That’s one of the longest workmanship guarantees in the residential construction space, and it covers waterproofing and tile as well as the plumbing rough-in.
Get a Free Tub-to-Shower Conversion Estimate in Santa Fe Springs
Call (888) 255-8179 for a free on-site estimate on your tub-to-shower conversion in Santa Fe Springs. A live person answers 24/7, and we’ll walk your bathroom, confirm whether the drain can stay put, and hand you a written, line-item price with the permit and inspection included. You’ll also hear about our current offers: $1,000 off projects over $10,000, 0% financing for 18 months, and a free project estimate and design consult.
Written by the team at Groundwork Construction Co.












