







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Patios, Walkways & Pool Decks in Santa Fe Springs: What It Costs and How Long It Takes
Patios, walkways & pool decks in Santa Fe Springs typically run $3,500 – $11,000 for a paver patio, with most walkway runs adding $1,200 – $3,500 and pool deck resurfacing landing in the same range as the patio itself. A straightforward back patio takes 3 – 5 working days from demo to final seal; larger layouts with drainage corrections or a full walkway loop run 1 – 2 weeks. Call (888) 255-8179 and we’ll walk your lot, check the grades, and put real numbers in writing before anything gets torn out.
How a Patio, Walkway or Pool Deck Job Actually Runs

We don’t hand you a start date and disappear. Here’s the real sequence, stage by stage, so you know what’s happening on your property and when you need to make a call.
Stage 1: Site walk and layout (day 1, about 90 minutes)
We measure the actual usable area, not the imagined one. On Santa Fe Springs lots, that usually means finding the property line, the gas meter, the hose bibs, and the downspouts. You’ll decide the shape and the paver or finish at the end of this visit, because layout drives everything downstream. If drainage is questionable, we check the fall with a level and flag it now rather than after demo.
Stage 2: Demo and excavation (days 2 – 3)
Old concrete, cracked patio slabs, or tired decking comes out first, then we excavate to depth. Base depth depends on what’s going on top: pavers want 4 – 6 inches of compacted Class II base with a fabric separator, poured concrete wants less. On the older ranch lots here we sometimes hit the original 1950s slab under the grass, which adds a half day of breaking and hauling. You’re deciding nothing at this stage – we’re just removing surprises before they cost you money.
Stage 3: Base, compaction and drainage (days 3 – 4)
This is the stage nobody sees and the one that determines whether your patio is flat in five years. Base goes in lifts, gets watered and plate-compacted, and we cut a slope of roughly 1 – 2% away from the house so water leaves the building. Near the 605 and 5 interchange the ground carries a lot of fine dust and silt, and we build the base to shed it rather than trap it. If your lot drains toward the neighbor, we discuss a channel drain or a dry well before the finish goes down.
Stage 4: Finish installation (days 4 – 7)
Pavers get laid in the pattern you picked, cut tight at edges and steps, and polymeric sand goes into the joints. Poured concrete gets forms, rebar or mesh, and a finish – broom, salt, or stamped. Pool decks get a slip-resistant surface and a coping detail that ties into the existing pool edge. You’ll want to be home for the finish day to confirm the color and pattern read the way you pictured.
Stage 5: Cleanup, seal and walkthrough (final day)
We haul everything out, wash the surface, and give you a walkthrough of the finished work. Sealer, where you’ve chosen it, goes on after the surface cures. That’s also when we hand over the 730-Day Done Right Promise in writing – if something settles, shifts, or doesn’t drain the way we said it would, we make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
What You’ll Choose Between: Materials, Grades and Finishes
The finish you pick changes the price, the maintenance, and how the space feels underfoot. Here’s the honest version of each.
- Concrete pavers (Belgard, Orco, Angelus): $3,500 – $11,000 for a typical patio. Best value over 20 years, repairable one stone at a time, and forgiving of minor ground movement. Downside: weeds in the joints if the polymeric sand isn’t refreshed every few years.
- Poured concrete, broom or salt finish: the low end of the patio range. Fast, clean, and cheap up front. It cracks. Every slab does. You live with visible hairline cracks or you pay for control joints that break up the look.
- Stamped or colored concrete: budget $2 – $5 more per square foot than plain pour. Looks like stone from the street; reads as shallow up close, and color flaking is a real risk on a hard inland-summer surface.
- Travertine or natural stone: the premium choice for pool decks because it stays cool underfoot in the sun. Higher material cost and more prep, but nothing else handles bare feet in August this well.
- Walkway width: 36 inches is the minimum for comfortable single-file, 48 inches lets two people pass. Going wider is about $12 – $20 per square foot of added area.
- Drainage systems: a channel drain, dry well, or French drain adds $800 – $2,500 depending on run length. On tight lots, this is not optional.
What Patios, Walkways & Pool Decks Cost in Santa Fe Springs, CA

Patio work here lands between $3,500 and $11,000, with the number driven mostly by square footage, base condition, and finish. Walkway runs typically add $1,200 – $3,500. Pool deck resurfacing and re-laying follow the same range as the patio, with travertine and other natural stones pushing toward the high end.
What moves a job to the low or high end:
- Square footage and shape. A clean 400-square-foot rectangle is the easiest money you’ll spend. Curves, multiple tiers, and cut-outs around planters cost more in cutting time.
- Existing condition. A flat, sound surface can sometimes be overlaid; a cracked, heaved slab gets demoed and re-based, which adds $1,000 – $3,000.
- Access. If a truck can’t get near the work area, everything moves by wheelbarrow, and that shows up on the invoice.
- Underground surprises. Relocating a sprinkler line, gas stub, or pool equipment conduit adds $400 – $1,500 per item.
- Finish grade. Natural stone, specialty stamps, and custom border patterns push toward the top of the range.
A written estimate should list demo, haul-off, base prep, drainage, material, and sealing as separate lines. It should not hide a “miscellaneous” line. What typically isn’t included: tree removal, gas or electrical line relocation by a licensed trade, and HOA architectural review fees. Our pricing is upfront – the number you see is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhat Santa Fe Springs Specifically Does to This Job
Santa Fe Springs is unusual: 1940s – 70s tract housing runs right up against refineries, warehouses, and truck yards off the 5 and 605. That industrial-grade dust and constant truck traffic settles on exterior surfaces, and patios and walkways near the freeway side of town wear visibly faster – pavers dull, joints fill, and concrete stains from airborne grit. We clean and re-sand those surfaces more often than we do on a quiet residential street in West Whittier-Los Nietos.
The housing stock matters just as much. On a typical 1950s ranch over in the 90670 pocket, we routinely find an original patio slab that’s heaved because the base was never compacted to today’s standard, or a hose bib that runs under the old walkway and needs rerouting before we pour. Original galvanized lines and undersized panels show up on these lots, which is exactly why we look before we dig.
Permitting is real here. Santa Fe Springs runs a design review and conditional-use process that adds time on industrial projects, and residential work needs permits pulled for any new concrete or structural patio cover. Seismic provisions in California code apply to any new structure – a pergola, a shade cover, a raised deck. We pull the permit and pass the inspection; you don’t chase paperwork. And the hot inland summers mean we schedule pours for early morning so the concrete cures evenly, not cracked from a fast, hot dry.
Serving Santa Fe Springs, CA – Our Local Coverage Area
We serve Santa Fe Springs and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions: Patios, Walkways & Pool Decks in Santa Fe Springs

A typical paver patio takes 3 – 5 working days, and a walkway loop adds 1 – 2 days on top. Larger jobs with drainage corrections, a pool deck resurfacing, or a stamped concrete overlay can run 1 – 2 weeks. Weather, cure time, and permit turnaround are the variables. Call (888) 255-8179 for a schedule that fits your timeline.
Yes for anything that adds structure – a raised patio, a shade cover, a pergola, or a pool deck rebuild that touches the pool shell. A flat-ground paver patio usually doesn’t require one, but the design review process here is strict, and it’s cheaper to confirm than to tear out. We handle the permit pull and the inspection.
Usually, yes. Most patios and walkways can be laid around existing hose bibs, gas stubs, and pool equipment. The exceptions are irrigation lines that run right through the footprint and any downspout that dumps onto the new surface – those need rerouting. We confirm this at the site walk, before demo starts.
Pool deck work typically lands in the $3,500 – $11,000 range, depending on square footage and finish. Travertine and other natural stones sit at the top; a simple cool-deck coating sits lower. Call (888) 255-8179 for an exact quote – estimates are free.
Every patio, walkway, and pool deck we install is covered by our 730-Day Done Right Promise – if it settles, shifts, or doesn’t drain the way we said it would, we make it right. That’s one of the longest workmanship guarantees in residential construction, and it’s in writing.
Get a Free Patio, Walkway or Pool Deck Estimate in Santa Fe Springs
Patios, walkways & pool decks in Santa Fe Springs come down to the base, the drainage, and the finish – and we quote all three in writing before we touch a shovel. Call (888) 255-8179 and a live person picks up, day or night. We’ll schedule a site walk, measure the space, and hand you a line-item estimate with no surprises. Estimates are free, and the 730-Day Done Right Promise backs every job.
Written by the team at Groundwork Construction Co.












