







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Lakewood, CA: What It Costs and How Long It Takes
An iron fence in Lakewood, CA typically runs $3,500 – $9,000 for a standard residential run, with most single-story tract homes landing between $4,200 and $6,800 depending on linear footage, height, and finish. Plan on two to four days on site for a typical 100 – 150 foot ornamental run: one day to set posts in concrete, a second to hang panels and gates, and a half day for finish and touch-up. Call (888) 255-8179 to schedule a free on-site estimate and get an exact number for your property line.
How We Build an Iron Fence, Stage by Stage

Iron work is a sequencing job. The fence is only as straight as the post line, and the post line is only as good as the measuring and layout that precedes it. Here’s what actually happens on a Lakewood job.
Stage 1: Site walk and layout (half a day). We measure the full run, mark the property line with the homeowner present, and confirm gate swings, post spacing, and height against any HOA rules. You decide panel style, height (usually 4, 5, or 6 feet), and gate placement at this stage. On a 1950s slab-and-stucco tract home, we also check where the fence will tie into existing walls, since the original stucco has often been patched or painted over multiple times.
Stage 2: Digging and setting posts (one full day). Post holes go down 24 – 30 inches, below the frost-free depth for this part of the LA Basin, and get set in concrete. This is the day that defines the whole job. If the ground runs into an old stub wall, tree roots, or the sidewalk easement, we adjust the line before any concrete is poured. You’ll want to be around for this day if you can; it’s the one point where a small change is cheap and everything after it is not.
Stage 3: Panel and gate installation (one to two days). Once the concrete has cured, which is 24 – 48 hours depending on weather, panels get set, leveled, and fastened. Gates go in last so they can be shimmed against the finished posts. Weld or bolt connections are made to spec, and moving parts get checked for swing clearance. You decide gate hardware (self-closing, latch style, hinge grade) at the start of this stage.
Stage 4: Finish and touch-up (half a day). Weld points get primed and coated, hardware gets checked, and the fence gets a final walk. On a powder-coated or painted iron fence, we touch up every spot we drilled or fastened. That’s the difference between a fence that rusts at the weld in year three and one that holds its finish through a decade of Santa Ana wind and marine-layer moisture.
Stage 5: Final walkthrough (one to two hours). We walk the line with you, check gate operation, confirm heights, and hand over the workmanship paperwork under the 730-Day Done Right Promise. If anything shifts or a hinge loosens in the first two years, we come back and fix it.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between on an Iron Fence
The biggest decisions on an iron fence are material grade, finish, and construction method. The trade-off isn’t really about style; it’s about how the fence holds up against moisture and wind over time.
- Wrought iron (solid, hand-forged): The most durable option and the most expensive. Heavy, hand-welded, and built to last decades. Suits homeowners who want a legacy fence and are willing to pay for it. Also the right call where the fence has to match an existing gate or architectural piece.
- Steel ornamental (tubular steel, welded or bolted): The standard choice for most Lakewood homes. Lighter than true wrought iron, holds up well, and costs meaningfully less per foot. The honest trade-off: cheaper tubular steel with a thin finish can start to rust at the weld and at ground contact in five to seven years in this climate.
- Powder-coated vs. painted finish: Powder coat is baked on and lasts far longer than liquid paint. It adds cost up front and saves repainting later. Painted finishes look good initially but need touch-up every few years, especially on the side facing the marine layer.
- Aluminum-look iron (cast aluminum): Lighter, will not rust, and holds a finish well. It’s a good fit for homeowners who want the iron look without the rust maintenance. The trade-off is that cast aluminum won’t take a hard impact the way steel will, so it’s less the choice for a driveway gate that gets bumped.
- Height and gate configuration: 4-foot runs cost less than 5- or 6-foot runs per foot, and a single walk gate is far cheaper than a driveway double gate. Most Lakewood homes go with a 4- or 5-foot front-yard run and a single 3-foot walk gate.
What Iron Fence Costs in Lakewood, CA

Iron fence pricing in Lakewood runs $3,500 – $9,000 for a standard residential install. Where a project lands inside that range comes down to four or five variables that actually move the number.
- Linear footage: The single biggest driver. Most Lakewood front yards run 80 – 150 feet of fence line, and every foot adds cost for both material and labor.
- Height and grade: 4-foot tubular steel is the low end; 6-foot wrought iron with hand-forged pickets is the high end. A step up in grade can double the per-foot material cost.
- Gate count and gate type: A single walk gate adds modestly; a driveway double gate with automation can push a project toward the top of the range or beyond it.
- Finish: Powder coat adds cost up front but avoids repainting. A liquid-painted finish is cheaper today and more expensive over ten years.
- Site conditions: Sloped lines, tree roots, old concrete, or a fence running along a shared property line with a neighbor’s unrepaired wall can add prep time. We quote it in writing before we dig so the number doesn’t move mid-job.
Every written estimate is line-itemed: posts, panels, gates, hardware, finish, and labor. We pull any required permits and the price you see is the price you pay, with no change orders unless you ask for a scope change. Our fence installation service pairs well with a fresh gate and entry, and homeowners often pair an iron fence with a new walkway from Patios, Walkways & Pool Decks in Lakewood so the whole entry reads as one design.
See the difference
Before
After
Before
After
Before
AfterWhat Lakewood’s 1950s Tract Homes Do to an Iron Fence Job
Almost every home here was built between 1950 and 1955 as part of one of America’s first planned communities, and those slab-on-grade tract houses have their own quirks once you start digging post holes. The original property lines often run along old stub walls, and the clay sewer laterals buried under the front yard are now at the age where a post hole can find one. We locate before we dig on every Lakewood job. The original 2×4 roof framing and single-pane windows are the front of the house; the fence is the back of the project’s story, and the two affect each other when a fence is being hung against patched stucco. The marine layer and Santa Ana wind cycles are the other half of the picture: they push moisture and grit against the fence finish, which is why we recommend a coated grade in Lakewood over a painted one. If your project grows into a full property re-do, we’d steer you to Fence Installation in Lakewood for the wider scope, and to ADU Design & Permitting in Lakewood if a garage conversion is also on the table. We cover the Lakewood ZIP codes 90712, 90713, 90714, and 90715.
Serving Lakewood, CA – Our Local Coverage Area
We serve Lakewood and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Iron Fence in Lakewood

An iron fence takes two to four days on site for a standard residential run, plus a 24 – 48 hour concrete cure between the post day and the panel day. Larger driveway gates or a run over 200 feet can stretch to a week, and the number on your written estimate reflects the timeline we actually commit to.
Yes, most iron fence installations in Lakewood require a fence permit, and height limits often depend on whether the fence is in the front yard or a side or rear yard. We handle the permit paperwork and confirm height and setback limits with the city before we order material, so nothing gets built then torn out.
An iron fence holds up to Lakewood’s marine layer and Santa Ana wind well if the finish and hardware are chosen for it. We recommend powder-coated steel or cast aluminum over a lightly painted finish, and we prime every weld and touch up every fastener at install.
An iron fence in Lakewood costs $3,500 – $9,000 for most single-story homes, with a standard run typically landing around $4,200 – $6,800. Linear footage, height, gate type, and finish grade are the biggest variables, and we provide a written line-item estimate before any work begins.
Every iron fence we install is covered by the 730-Day Done Right Promise: if it isn’t done right, we make it right for two full years. That covers workmanship from the post set to the panel hang to the gate hardware, and it’s backed in writing on every job.
Get a Free On-Site Estimate for Your Iron Fence in Lakewood
Call (888) 255-8179 and we’ll set up a free on-site estimate for your iron fence in Lakewood. A live person answers around the clock, so you’re not waiting on a callback. On the visit we measure the line, confirm gate swing and height, walk you through finish options, and leave you with a written line-item price: the number you see is the number you pay. Estimates are free, and financing is available at 0% for 18 months if you want to spread the cost.
Written by the team at Groundwork Construction Co.












