







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Bellflower, CA: What It Costs and How Long It Takes
A wrought iron fence in Bellflower typically runs $3,500 to $9,000 for a standard residential run, and most jobs wrap up in two to four working days once the panels are fabricated. That figure covers tear-out of the old fence, post setting, panels, and finish. Anything with masonry piers, automation, or a tight alley lot pushes toward the top of that range. Call (888) 255-8179 for a free on-site estimate before you commit to a number.
How We Build an Iron Fence, Stage by Stage

Iron fence work is simple in principle and unforgiving in the details, especially on Bellflower’s small mid-century lots where the property line is often a guess. Here’s the sequence you can plan around.
Stage 1: On-site measure and line check
Day one is a walk of the property with a tape, a line of sight, and a look at whatever the old fence left behind. We confirm the run length, gate positions, and where the fence ties into the house or a side wall. On Bellflower lots, this is also where we flag a buried sprinkler line or a shared boundary that isn’t where the plat says it is. You decide the gate count and swing direction at the end of this visit. About 45 to 90 minutes.
Stage 2: Demo and post layout
Old fence comes down first, usually a half day for a typical backyard run. Then we set string lines and mark every post center. Post spacing is driven by the panel width you choose, typically 6 feet on center for a standard residential iron fence. This is the stage where a fence either lines up square or doesn’t, and you’ll see the layout marked before a single hole is dug. One working day.
Stage 3: Post holes and concrete
Posts go in at roughly 24 to 30 inches deep in a footing, deeper at gate posts, and everything gets set in concrete. On the older Bellflower blocks where soil is compacted fill over decades of yard rework, we sometimes hit old footings or a stray slab from a previous project. Cure time matters here, so we generally don’t hang panels the same day. One to two working days, including cure.
Stage 4: Panel and gate install
Once the footings hold, panels go up and gates get hung, aligned, and checked for swing. Welded seams and pickets get touched up on any scratches from handling. You’ll walk the run with us and confirm gate latches and clearances. Half a day for a standard run, longer if the layout is irregular.
Stage 5: Punch walk and cleanup
Final pass covers hinge tension, latch adjustment, and a chemical touch-up on any weld or cut point. We haul off the old fence and sweep the line. You sign off on the run, and the 730-Day Done Right Promise covers the workmanship from that day forward.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Actually Choose Between
Iron fence isn’t one product. The choices below move both the price and how the fence ages on a Bellflower property.
- Wrought iron vs. steel vs. aluminum: True wrought iron is the heaviest and most expensive, and it holds up for decades. Steel is the practical middle ground. Aluminum looks similar at the lightest weight and lowest cost but dents more easily. For a residential run in this climate, steel is usually the honest sweet spot.
- Powder coat vs. paint finish: Powder coating resists chipping and sun fade far better than paint, which matters in Bellflower’s hot, dry summers that bake exterior finishes. It costs more up front and pays back in fewer repaint cycles.
- Panel style and picket spacing: Flat-top, spear-top, and ornamental scroll patterns all price differently. Tighter picket spacing costs more per linear foot because more material goes into the panel.
- Gate automation: A manual gate with a self-closing hinge is standard. Adding a keypad, remote, or intercom runs a few hundred to over a thousand depending on the operator and wiring run.
- Masonry piers and caps: Brick or block piers on the gate posts look strong and add real cost. On Bellflower’s compact lots, a pair of piers often reads better than a long straight run.
What Iron Fence Costs in Bellflower, CA

Most residential iron fence projects here land between $3,500 and $9,000. That range is honest for a run in the 80 to 150 linear foot range with a gate or two. Here’s how to read the low and high end.
- Run length: Linear footage is the biggest lever. A short side-yard enclosure sits near $3,500. A full perimeter with front and back runs pushes to $9,000.
- Material grade: Steel with a powder coat sits in the middle. True wrought iron and heavy ornamental patterns push toward the top.
- Existing fence and demo: Old wood or chain link demo, plus footing removal, adds labor. A clean slate is cheaper.
- Gate count and automation: Each gate adds material and hardware. Automated gates add the most.
- Masonry and special finishes: Piers, custom scrollwork, and two-tone finishes add cost beyond a standard panel run.
A written estimate lists panel type, finish, post count, linear footage, gate hardware, and demo. What it usually excludes: masonry piers, automatic gate operators, and any repair to a shared boundary wall. Upfront pricing means the number on the estimate is the number you pay, provided the scope doesn’t change during the job.
See the difference
Before
After
Before
After
Before
AfterWhat Bellflower Homes Specifically Do to This Job
Bellflower’s housing stock is mostly post-WWII stucco tract homes on tight lots, many with detached garages at the back of a shallow lot. That layout changes iron fence work in ways that don’t show up in other local markets. The side-yard run is often just wide enough for a fence and a walkway, so post holes and gate swings have to be set with the neighbor’s line in mind. On the older blocks, it’s not unusual to find a converted garage or an unpermitted room addition that shifts where a fence can legally land, and we’ve had to redraw gate positions after a plan check pointed it out. The hot inland-LA summers also work on the finish, so powder coat or a proper primer pays off here more than in cooler zones. If the iron fence is part of a full Fence Installation in Bellflower scope that includes repairs further back, we’ll point it out during the estimate. Homeowners in the 90706 and 90707 ZIPs can count on us covering Bellflower fully, and where the fence adjoins a rear yard project, it pairs naturally with Patios, Walkways & Pool Decks in Bellflower or an ADU Design & Permitting in Bellflower project. Our broader Fence Installation work covers the same drilling and footing approach.
Serving Bellflower, CA – Our Local Coverage Area
We serve Bellflower and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Iron Fence in Bellflower

Most residential iron fence jobs here take two to four working days from demo to punch walk, depending on run length and gate count. Fabrication of panels can add a week or more, and we schedule install around that lead time so the yard isn’t torn up while you wait. Call (888) 255-8179 to get a timeline for your exact run.
Most residential iron fence runs in Bellflower don’t require a building permit, but the city does limit fence height, and corners near the street have sight-line rules. We check the local limits during the estimate so the fence you want is one you can build. Call (888) 255-8179 to confirm the rules for your lot.
Yes. We hand-dig post holes where a sprinkler line, gas lateral, or irrigation run is in play, and we avoid trenching unless gate wiring needs it. On older Bellflower lots, we always call in a utility locate before digging. Call (888) 255-8179 for a site visit before we commit to a layout.
A short side-yard fence with one gate usually runs around $3,500 to $5,000, and a full perimeter typically lands between $6,000 and $9,000. The number moves with linear footage, finish, and gate count. Call (888) 255-8179 for an exact written quote.
Every iron fence project we do is backed by the 730-Day Done Right Promise. If the workmanship fails within that window, we come back and make it right. Call (888) 255-8179 to review the warranty in writing with your estimate.
Get a Free Iron Fence Estimate in Bellflower
We’ll come measure the property, walk the line with you, and hand you a written estimate with the panel type, footage, and finish spelled out. If a permit or a garage conversion already on the lot changes the layout, we’ll flag it then. Call (888) 255-8179 to schedule your free estimate, and a live person will pick up.
Written by the team at Groundwork Construction Co.












