







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Artesia, CA: What You’re Actually Getting
An iron fence in Artesia runs $3,500 to $9,000 installed, most commonly finishing in the $4,800 to $7,200 range for the typical 80 to 120 linear feet across the front and one side of a 1950s tract lot. We handle design, city approvals, excavation, and set posts in one continuous sequence, usually 4 to 7 working days start to finish. Call (888) 255-8179 for a free on-site estimate with a written line-item quote before anything gets ordered.
The number jumps around a lot in this city specifically, and the reasons are worth understanding before you sign anything. More on that below.
How an Iron Fence Actually Gets Built Here

Iron fence work in Artesia is not complicated, but it’s unforgiving. Posts that aren’t set to the right depth on this old fill-heavy soil will lean within two rainy seasons. So the sequence matters more than the materials you pick.
Day 1: Site walk and dig
We stake the layout, call for utility locates (that takes 2 to 3 business days in most cases, so we schedule it in advance), and mark every post location with paint. You approve the final alignment before any digging starts, because once a post is in, moving it means concrete work. On tight lots near Pioneer Boulevard and along the older streets off 183rd, we often have to hand-dig because there’s simply no machine access between the house and the property line.
Day 2 to 3: Footings and set
Each post gets a concrete footing poured to a minimum of 24 inches deep, 30 inches on gate posts, because a gate carries load and corner posts take wind the straight sections don’t. Concrete cures 24 to 48 hours before any load goes on the posts. You choose the post cap style and the finial at this stage if you haven’t already.
Day 3 to 4: Rails and pickets
Rails get welded or bolted to the posts depending on the system you picked, then pickets go in. We set spacing to your spec (standard is 4 to 4.5 inches, tighter stalls deter dogs and small pets but cost more per foot). This is the day you can see the fence and change your mind on any detail before it’s locked in.
Day 5 to 6: Gates and hardware
Gate frames hang, hinges get set, latches and closers mount, and the gate swings get adjusted for clearance. This is where the biggest cost swing happens on most Artesia jobs, because an alley-facing driveway gate is a heavier build than a 3-foot pedestrian gate, and most homes here have both.
Day 6 to 7: Finish, punch, and inspection
Touch-up on any weld marks or scratches, a final walkthrough with you where we measure picket spacing and check every gate swing, and if the job triggered a permit, the city inspection. You sign off at the end, and the 730-Day Done Right Promise covers the workmanship for two full years from that date.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Iron Fence Options: What You’re Choosing Between
Iron isn’t one material. What you buy at the low end and the high end are genuinely different products that age differently in Artesia’s climate.
- Wrought iron (solid bar, forged look) – the classic. $65 to $110 per linear foot installed. Heavy, beautiful, and it will outlive the house if it’s maintained. Requires repainting every 5 to 8 years.
- Tubular steel (hollow, welded) – $45 to $75 per linear foot. Much lighter than wrought iron, faster to install, and most of what you see on newer homes. Can dent on impact where wrought iron bends.
- Aluminum (cast or extruded) – $55 to $90 per linear foot. Doesn’t rust, lighter still, and holds a powder-coat finish much longer than steel holds paint. The honest trade-off: it can’t take the same physical abuse as steel.
- Powder coat vs. wet paint – powder coat runs $8 to $18 per linear foot more upfront but typically lasts 10 to 15 years before fading versus 3 to 5 years for wet paint in full sun. Worth it on south- and west-facing runs.
- Picket spacing – 4-inch standard, 4.5-inch for a more open look, 2-inch “pool code” spacing if the fence borders a pool (required by California pool safety code and not optional).
- Gate style – walk gates ($600 to $1,800 each), driveway gates ($1,500 to $4,500 depending on width and whether it’s manual or has an opener), and rolling gates for alley access where there’s no room for a swing.
The other variable most people don’t think about is finish color. Black is standard and cheapest; custom bronze and rust finishes cost $10 to $20 per linear foot more and read very differently on an older Artesia ranch home than they do on a 1990s build. We’ll bring color chips to the estimate so you’re deciding in place, not from a brochure.
What an Iron Fence Costs in Artesia, CA

Most iron fence work in Artesia lands between $3,500 and $9,000. That’s the honest range. Here’s what actually moves a job to one end or the other.
| Line item | Typical range |
|---|---|
| Wrought iron, 100 linear feet | $6,500 – $11,000 |
| Tubular steel, 100 linear feet | $4,500 – $7,500 |
| Aluminum, 100 linear feet | $5,500 – $9,000 |
| Walk gate (3-4 ft) | $600 – $1,800 |
| Driveway gate (12-16 ft) | $1,500 – $4,500 |
| Automatic opener (if desired) | $1,200 – $2,800 |
| Removal of old fence | $300 – $900 |
| Permit (when triggered) | $150 – $500 |
The 4 to 5 variables that push you to the top of that range: total length beyond 100 feet, a driveway gate with an opener, tight-access sites where we hand-dig (adds 1 to 2 days of labor), a pool code requirement, and removal of an existing block or wood fence. A written estimate from us lists every one of those line by line, so you can see exactly which ones apply. Nothing shows up later as a change order. The number you see is the number you pay.
Two standing offers matter on a job this size: 0% financing for 18 months and $1,000 off any project over $10,000 (a larger iron run, or a combined fence-and-patio job). Ask about both when we come out.
See the difference
Before
After
Before
After
Before
AfterWhat Artesia Homes Specifically Do to an Iron Fence Job
Artesia’s housing stock is 1950s and 1960s single-story tract homes on small parcels, many with later additions and enclosed patios that were never permitted. That matters to a fence in concrete ways. First, property lines on these old lots often don’t match the assessor’s map, especially after decades of informal enclosures, so we measure from a verified survey (or recommend one) before setting the first post. Second, many of those enclosed patios and converted garages sit within 3 to 5 feet of the fence line, which changes the post-and-panel alignment you can actually achieve.
During the pre-construction walkthrough we regularly find “phantom” square footage in these old tracts, garages (or what the map calls a garage) enclosed decades ago without permits. That discovery sometimes turns a fence job into a larger conversation about reconciling the structure with current code, which is where our Fence Installation in Artesia scope and a broader permitting review can overlap. If the addition eventually needs a proper permit, we often point people toward our ADU Design & Permitting in Artesia service for the paperwork side.
The city plan-check office on these jobs is known for strict review, so when we do trigger a permit (unusual for a fence under 6 feet, but required for most taller runs and pool barriers), we build the plan set to pass first time. That avoids the 2 to 4 week resubmittal cycle we see on jobs that go in half-prepared. Artesia’s distinct here: a smaller city with a small office and a thorough reviewer, which is actually to your benefit if the plan is built right.
On the soil side, the older lots sit on fill-heavy ground, and the winter rain bursts we get through the coastal basin will find any post set too shallow. We set every post 24 inches deep minimum, deeper on corners and gates, because a leaning iron fence is a permanent eyesore. If you’re doing a hardscape job at the same time, homeowners often pair this with Patios, Walkways & Pool Decks in Artesia so the fence and the drainage work get solved together. We cover 90701 and 90702, and if you’re just outside the border, check the Artesia service area to confirm. For anything beyond fence, our Fence Installation service has the full project scope.
Serving Artesia, CA – Our Local Coverage Area
We serve Artesia and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Iron Fence in Artesia

Most jobs run 4 to 7 working days from first dig to final walkthrough, with the utility locate taking 2 to 3 extra days at the front if we haven’t already scheduled it. A small 40-foot run can finish in 3 days; a full perimeter with two gates and a driveway opener runs closer to 8. The biggest variable is site access. On tight lots off 183rd and near Pioneer, hand-digging adds a day or two versus an open lot where a machine can reach the line.
Fences under 6 feet generally don’t require a permit; anything over 6 feet, pool barriers, and most retaining-fence combinations do. The strict plan-check at the city office means the permit set has to be built correctly the first time. We pull the permit for you and pass the inspection as part of the job, and the fee is listed as a line item in the estimate. If you’re unsure whether your fence triggers a permit, call (888) 255-8179 and we’ll tell you straight before the estimate.
Most iron fence work in Artesia costs $3,500 to $9,000, with a typical 100-foot run landing at $4,800 to $7,200. Tubular steel runs lower than wrought iron; driveway gates and openers push the number up. Removed fencing, pool code spacing, and tight-access sites add to the total. Call (888) 255-8179 for a free on-site estimate with every line item spelled out.
Yes, in most cases. An iron fence with 24-inch footings can usually be routed around existing plantings and set within 12 inches of an enclosed patio without disturbing the structure. What we can’t avoid: removing any fence panels currently blocking the line, and cutting back roots within the footing diameter. If the old enclosed patio needs structural work, we’ll flag it during the walkthrough and let you decide whether to address it now or later.
Workmanship is covered by the 730-Day Done Right Promise: if the fence isn’t done right, we make it right for two full years from the sign-off date. Material warranty is separate, supplied by the manufacturer, usually 1 to 5 years on finish depending on the product. If a post leans within two years because we set it too shallow, that’s on us, and we come back and fix it.
Schedule Your Iron Fence Estimate in Artesia
Call (888) 255-8179 to schedule a free on-site estimate for your iron fence in Artesia. We come out, measure the actual line, check access and utilities, and leave you with a written line-item quote the same visit. No-pressure, no hidden fees, and every number explained before you commit. Our technicians are background-checked and arrive in uniform, and calls are answered by a live person 24/7. Financing and current promotions can be discussed on that same call.
Written by the team at Groundwork Construction Co.












