







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Custom & Geometric Windows in Whittier: What the Job Actually Involves
Custom & Geometric Windows in Whittier run about $6,500 to $28,000 installed, depending on how many openings you’re shaping and whether the frames are built to order. Most single-room projects – an arched set over a Spanish Colonial entry, a triangular gable window, a round accent in a stairwell – land in the $9,000 to $15,000 range and take two to four weeks from template to final trim. Call (888) 255-8179 and we’ll walk your openings on site before anyone quotes a number.
The Process: From Walk-Through to Final Trim

Geometric work isn’t a pick-from-catalog job. Every angle and radius gets measured, templated, and built, and the sequence matters. Here’s how it runs on a Whittier project.
Stage 1: On-site measure and template (day 1, 2 to 3 hours)
We measure every opening, check the framing and sheathing, and confirm the rough opening is square and plumb. On curved or angled units, we template the shape physically or with a laser scan. You decide the shape, glass type, and frame material at this stage, and we tell you honestly if a wall can’t carry what you’re picturing without structural work.
Stage 2: Written line-item estimate and permit pull (days 2 to 5)
You get a written quote that breaks out each unit, the glass, the trim, the labor, and the permit fee. Whittier projects inside the historic overlay near Uptown often need a design-review sign-off before the building permit issues, which can add two to four weeks. We tell you upfront which track your address is on.
Stage 3: Fabrication (three to six weeks, longer on true custom shapes)
Angled and radius frames are built to order, so lead time depends on the complexity and the manufacturer. Straight-line picture windows move fastest; half-rounds, trapezoids, and radius-top units take the longest. You’re not waiting idle – we schedule demo and prep around the delivery date.
Stage 4: Removal and rough-in (days 1 to 2 of install)
Old units come out, the rough opening is cleaned and reframed as needed, and the new frame is set, shimmed, and flashed. On a 1920s Craftsman, reframing is common because original framing has moved over the decades. We check for rot and water damage before anything gets sealed in.
Stage 5: Glazing, trim, and inspection (days 2 to 4 of install)
Glass goes in, the unit is weather-sealed, interior and exterior trim is fit to the shape, and we walk the job with you. If a permit was pulled, the inspection closes it out. Most single-room installs finish in two to four install days depending on how many units and how complex the shapes are.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Actually Choose Between
Geometric windows open a wider menu than standard rectangles, and each choice moves both the look and the price. Here’s what most Whittier homeowners weigh:
- Frame material: Vinyl is the value play and handles the dry Puente Hills heat well, but it can’t be shaped into tight curves easily. Wood and aluminum-clad wood take any profile and suit the Craftsman and Spanish Colonial stock near Uptown, and cost more. Fiberglass sits between them on price and holds up to sun and temperature swings.
- Glass package: Dual-pane with low-E and argon is the standard for California climate zones, and it cuts heat gain in a west-facing gable. Triple-pane adds cost and weight and rarely pays back here. Tempered glass is required on units near doors and low to the floor.
- Shape and configuration: Arches, half-rounds, trapezoids, and full circles each carry a different fabrication premium. A true radius costs more than a segmented arch built from straight mullions. You’ll decide how literal the geometry needs to be.
- Finish and trim: Interior trim in stained wood versus painted MDF, exterior in stucco-return versus clad trim, changes both price and how the window reads on a stucco Spanish Colonial facade.
- Brands: We work with manufacturers that build true custom geometry, including CGI and CWS for shaped and specialty units, and ECO Window Systems for energy performance. Your estimate names the exact line and model so there’s no mystery later.
What Custom & Geometric Windows Cost in Whittier, CA

Custom & Geometric Windows in Whittier typically run $6,500 to $28,000, with the average single-room project in the $9,000 to $15,000 range. A single accent unit might come in near the low end; a whole facade of shaped windows lands near the top. These are real ranges, and here’s what pushes a job from one end to the other:
- Number and complexity of shapes: Straight picture windows are the cheapest per unit. Every radius and angle adds fabrication cost.
- Existing condition: Reframing a century-old opening, repairing rot, or shoring up a load-bearing wall adds cost. A clean newer opening costs less.
- Glass and frame grade: Vinyl dual-pane is the low end; clads wood with custom glass is the high end.
- Permit scope: A standard building permit runs a few hundred dollars; historic-overlay design review adds time and fees.
- Trim and finish: Custom interior and exterior trim, especially on curves, adds labor.
Your written estimate lists each unit, glass spec, trim, labor, and permit line, so the number you see is the number you pay. What’s typically not included: structural repair discovered behind the wall, and lead-paint abatement on pre-1978 homes. We flag both before work starts, not after.
See the difference
Before
After
Before
After
Before
AfterWhat Whittier Homes Specifically Do to This Job
Whittier’s housing stock is split, and the split changes how a geometric window job runs. The historic Uptown core around 90601 is full of 1910s-1950s Craftsman and Spanish Colonial homes inside a state-designated historic overlay. A shaped window swap there can trigger design-review, which adds weeks. Across the eastern tracts in 90604 and 90606, the same scope is often a same-week permit pull. Those mid-century ranches sit on slab-on-grade with original galvanized plumbing and undersized panels, so we plan electrical and framing around that reality. The semi-arid basin at the foot of the Puente Hills bakes stucco and dries out wood siding, and Santa Ana wind episodes drive heat and grit against west-facing glass. That’s why we spec low-E glass and tight flashing on every Whittier install – the sun here is unforgiving on anything less.
Serving Whittier, CA – Our Local Coverage Area
We serve Whittier and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Custom & Geometric Windows in Whittier

A single-room project usually runs four to eight weeks from signed estimate to final trim, split between one to two weeks of measure and permitting, three to six weeks of fabrication, and two to four install days. Historic-overlay addresses near Uptown can add two to four weeks for design review. Call (888) 255-8179 for a timeline on your specific openings.
Yes, most geometric window work requires a building permit because it changes the envelope and often the structural opening. Homes inside the historic overlay also need design-review sign-off. We pull the permits and pass the inspections as part of the job, so you’re not chasing the city. Call (888) 255-8179 and we’ll confirm your address’s track.
Often yes, if the opening is sized to the existing framing and the wall is non-load-bearing. Shaped units that fit within the current rough opening are the easiest path. If a shape needs a wider header or a relocated pipe, that’s a structural and plumbing add we scope and price before work starts. Estimates are free – (888) 255-8179.
Expect $6,500 to $28,000, with most single-room jobs landing between $9,000 and $15,000. Shape complexity, frame material, glass package, and permit scope drive the number. Call (888) 255-8179 for an exact written quote – estimates are free and line-itemed.
Every custom & geometric window project is covered by our 730-Day Done Right Promise – if it’s not done right, we make it right, backed in writing. Manufacturer glass and frame warranties pass through to you as well. Call (888) 255-8179 to see the full terms before you sign anything.
Get a Free On-Site Estimate
If you’re shaping a facade or replacing an odd-shaped opening, start with a free on-site estimate. Call (888) 255-8179 and a live person answers, day or night. We’ll walk your openings, confirm your permit track, and hand you a written line-item quote with no surprises. Much of this work pairs naturally with a wider Windows & Doors in Whittier scope, and homeowners often pair new windows with Concrete Driveways & Concrete Work in Whittier or Asphalt Driveways & Resurfacing in Whittier while crews are already on site. We cover all of Whittier and the surrounding ZIPs.
Written by the team at Groundwork Construction Co.












