







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Metal Roofing in Downey, CA: What It Costs and How the Job Runs
Metal roofing in Downey typically runs $15,000 to $40,000 for a full roof, with most single-story ranch homes landing in the $18,000 to $28,000 range. The job takes three to seven days on an average Downey house once permits clear, and the roof itself should outlast the mortgage you have on the place. Call (888) 255-8179 for a free on-site estimate with a written line-item quote.
How a Metal Roof Goes On a Downey House, Start to Finish

Metal roofing isn’t a one-day swap. The sequence matters more than the material, and on older Downey homes the prep work is where the job lives or dies. Here’s the order we work in.
Day 1: Tear-off and deck inspection
We strip the old roof down to the sheathing, usually one to two days depending on layers and square footage. Once the deck is exposed we walk it board by board, because on 1950s Downey tract homes we regularly find soft spots, undersized nailing, or skip-sheathing from the original build. Anything that won’t hold a fastener gets replaced before a single panel goes up. This is the stage where surprises live, which is why the deck is itemized separately in the written quote.
Day 2: Deck repair, underlayment, and flashing
Bad sheathing gets sistered or replaced. Then a high-temp synthetic underlayment goes down over the whole field, followed by ice-and-water membrane in the valleys and around penetrations. Flashing at the chimney, vent stacks, and wall transitions gets fabricated or fitted. On metal roofing this stage is the waterproofing engine; the panels are the rain screen, not the seal.
Day 3 to 5: Panel or shingle installation
This is where you’ll decide between panel types and how they’re attached. Large-format panels go on faster than individual stamped shingles but need more careful layout. Concealed fasteners install slower than exposed ones and cost more. Expect the bulk of the roof finished in this window on a standard Downey ranch footprint. Second-story and complex hip-and-valley roofs push it out a day or two.
Day 5 to 6: Ridge caps, trim, and penetrations
Ridge, hip, and rake trim go on, then vent boots, exhaust caps, and any new skylight flashing. Every penetration gets sealed and checked twice, once by the installer and once by the lead. This is the stage most likely to be skipped on a rushed job, and the stage most likely to leak six months later.
Day 7: Final inspection and walkaround
We pull the Downey permit sign-off, sweep the yard for nails with a magnet, test the gutters and downspouts, and walk the roof with you. You get the paperwork, the warranty documentation, and the touch-up kit for any field scratches. The 730-Day Done Right Promise covers workmanship from the day we hand you the keys, so if a fastener backs out or flashing lifts, we’re back on your roof.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Metal Roofing Options You’ll Actually Choose Between
Three decisions drive most of the price and long-term performance. Get these right and the roof lasts 40 to 50 years.
- Standing seam panels vs. exposed-fastener panels: Standing seam hides the fasteners, expands and contracts cleanly, and lasts the longest. It costs the most. Exposed-fastener panels (screw through, with a washer) cost less but the screws become the maintenance item, and every screw is a potential leak point down the road.
- Steel vs. aluminum: Steel is the workhorse and what we install most in Downey. Aluminum costs a bit more but handles coastal humidity better if you’re anywhere near the marine influence. Stone-coated steel adds texture and looks like tile or shake from the street.
- Stamped shingle/tile profile vs. flat panel: Stamped profiles look like traditional roofing and blend with the Spanish-eclectic and ranch architecture of Downey’s housing stock, which helps at resale and with any HOA review. Flat panels are the modern/industrial look and read cleaner on mid-century ranch lines.
Finish is the fourth choice. Kynar-based painted finishes hold color longer than standard painted steel; bare galvanized is cheaper but weathers to gray and I don’t recommend it for a home you plan to keep.
What Metal Roofing Costs in Downey, CA

Full metal roof installation in Downey runs $15,000 to $40,000, with a typical single-story ranch landing near $18,000 to $28,000. Roof repair on an existing metal roof is a different, smaller job in the $400 to $1,800 range and is usually folded into a larger scope. Five variables push the number up or down:
- Square footage and roof complexity. A simple gable roof is the cheapest per square. Hip-and-valley, dormers, multiple roof lines, and second-story work add labor and waste.
- Deck condition. Original 1950s sheathing often needs partial replacement. We itemize this so you see the cost before work starts.
- Panel type and gauge. Standing seam over 24-gauge steel sits at the top of the range; exposed-fastener panels in lighter gauge sit at the bottom.
- Number of penetrations and skylights. Each vent stack, chimney, or skylight adds flashing labor and a potential failure point.
- Permit scope. A straight re-roof pulls a simpler permit than one with structural repair, and any added structural work pushes the number.
The written quote covers materials, labor, tear-off and disposal, underlayment, flashing, and permit fees. It doesn’t cover hidden structural repair (until we open the deck and show you), gutter replacement if your existing gutters aren’t reusable, or a full solar re-install if you have panels up there. Every estimate is itemized so nothing on the page is a mystery when the invoice arrives.
See the difference
Before
After
Before
After
Before
AfterWhat Downey’s Housing Stock Does to a Metal Roofing Job
Downey is a built-out, post-war inner-ring suburb, and the work here reflects it. Most of what we install metal roofing on sits on 1940s to 1960s single-story ranch and Spanish-eclectic tract homes on tight lots – especially around Furman Park and the original 1950s neighborhoods. That era of house has shallow stem-wall or slab foundations and original roof framing that was never engineered for the wind uplift of a full standing-seam system, so our first trip is often a structural look at the rafters and the sheathing before we quote panel layout. Downey’s plan-check process cares about that too, and the city’s historic-preservation identity around the original ranch tracts means exterior changes get reviewed with an eye on the streetscape, so profile and finish matter as much as wind rating. The inland summer heat bakes the deck through the day and drives early morning start times; our crews typically begin at 6:30 a.m. on Downey jobs to get the panels laid before the sun is on the west slope. We cover all of Downey plus the neighboring areas, and this is a straight metal roofing scope whether it’s part of a bigger Roofing in Downey project or a standalone re-roof.
Serving Downey, CA – Our Local Coverage Area
We serve Downey and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Metal Roofing in Downey

A typical single-story Downey ranch takes three to seven days from tear-off to final walkaround, with the permit wait on the front end. Complex roofs, second stories, and significant deck repair push it to the longer end. Call (888) 255-8179 and we can give you a realistic window on your specific roofline.
Yes. Downey issues re-roof permits for metal installations, and if the work involves structural repair or sheathing replacement the scope expands. We pull the permit for you, schedule the inspection, and pass it before we call the job done. No permit, no final sign-off, and no honest warranty.
Most metal roofing should be installed over a clean, inspected deck, which means tear-off. Skip-sheathing over an old roof traps moisture and hides deck rot. On Downey’s older housing stock we almost always recommend full tear-off so we can see what the 1950s framing is actually doing.
Full installation runs $15,000 to $40,000 for a Downey home, with most jobs landing in the $18,000 to $28,000 range. Roof repair on existing metal is $400 to $1,800. Call (888) 255-8179 for an exact quote – the on-site estimate is free and itemized.
Panel manufacturer warranties run 30 to 50 years depending on finish and gauge; separate from that, every installation is covered by our 730-Day Done Right Promise on workmanship. Two warranties, one written line-item quote, and a live person answering the phone.
Not on the scope we quoted. If we open the deck and find rot or undersized framing that wasn’t visible before, we stop, show you photos, and get your approval on the added line item in writing before we touch it. Upfront pricing, no surprises.
If window upgrades are on your list while the roof is off, homeowners often pair this with Window Replacement in Downey to cut cooling bills, or step up to Impact Windows & Doors in Downey for the extra strength. Both fit naturally into a full exterior scope, and we handle them with the same Roofing team sequencing so you’re not managing two contractors.
Get a Written Metal Roofing Quote for Your Downey Home
The estimate is free, on-site, and itemized line by line. You’ll get the panel options, the finish choices, the deck condition notes, and the permit scope in writing before anything is ordered. Our technicians have up to 12 years of experience on metal systems, and pricing is fixed once the scope is signed. Call (888) 255-8179 – a live person answers around the clock – and we’ll get your Downey metal roofing question answered the same call, or schedule the walk-through.
Written by the team at Groundwork Construction Co.












