







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Metal Roofing in South Whittier: What It Takes and What It Costs
A metal roof on a South Whittier house typically runs $15,000 – $40,000 installed, and most single-story homes here are finished in 3 – 6 working days once materials land on site. The work covers tear-off of the old roof, decking repair where it’s soft, new underlayment, and the panels or shingles themselves, plus a Class A assembly that matters in this wind corridor. Call (888) 255-8179 to schedule a free on-site estimate.
How a metal roof actually gets built here, stage by stage

Metal isn’t a one-day job, and anyone who tells you it is hasn’t done one on a 1950s South Whittier tract house. Here’s the real sequence, with the decisions you’ll make along the way.
Day 1: tear-off and deck inspection
We strip the existing shingles or gravel down to the sheathing, which on these homes is usually 1×6 skip sheathing rather than modern plywood. That’s the first place a metal job can surprise you: skip sheathing has to be overlaid with solid decking before any panel goes down, or the roof will telegraph every board once it heats up. You’ll decide at this point whether to recover with new OSB or plywood. Budget a day for this on a typical 1,400 – 1,800 sq ft roof.
Day 2: underlayment, flashing, and edge metal
We roll out a high-temp synthetic underlayment and set the eave and rake trim, then work the penetrations: vent stacks, the furnace flue, and the transition where the patio cover ties into the house. Flashings get done before panels, always. This is the stage that decides whether the roof stays dry for 40 years, so it gets a full day and your roofer should walk it with you.
Day 3 through 5: panel or shingle install
Standing seam panels run in long courses, so the crew sets them in sequence from eave to ridge, which keeps the seams straight and lets us close out the ridge last. Stone-coated steel shingles go faster because they interlock like regular shingles. A straightforward gable roof on a South Whittier single-story closes out in two or three days; a hip roof with dormers or a detached garage adds a day.
Day 6: vents, ridge cap, and final walk
We finish the ridge vent, install ember-resistant vents where the roof meets the attic, and sweep the gutters for metal shavings, which will rust-stain a concrete driveway if they’re left. You get a walkthrough: photos of the decking before it was covered, the flashing details, and the paperwork for the permit final.
Inspection sign-off
Because South Whittier is unincorporated, that final goes through LA County Public Works, not a city building department. We schedule it and meet the inspector on site so you don’t have to take a day off. If anything gets flagged, we correct it before we call the job done.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The metal roofing options you’ll actually choose between
Most of the price swing on a South Whittier metal roof comes down to three decisions, and none of them is a trick question. Here’s how they shake out.
- Standing seam vs. stone-coated steel shingles. Standing seam is the premium choice: concealed fasteners, 40-plus year service life, and the cleanest look on a low-pitch roof. It runs at the top of the metal range. Stone-coated steel shingles run lower, install like shingles, and give you a tile or shake profile without the weight. Fasteners are exposed, so they’re the option to skip on a steep, wind-exposed slope.
- Panel gauge and substrate. The panels themselves are 24- or 26-gauge steel, or aluminum if you want zero rust risk. Aluminum costs a little more and is the right call near the coast or anywhere salt air reaches. It’s the difference between a roof that holds its finish for 30 years and one that starts to chalk.
- Color and finish. Standard Kynar 500 finishes in a dozen colors are cheapest; a custom color adds a premium and a few weeks of lead time. On a South Whittier stucco house, most homeowners land on a medium brown, charcoal, or a clay tone that reads like tile from the street.
- Fire rating. A Class A assembly is the real decision, not an upgrade. With Santa Ana winds pushing fire risk, the ember-resistant ridge and eave vents that come with a Class A system are worth specifying up front. Your insurer may ask about them.
What Metal Roofing costs in South Whittier, CA

Metal Roof Installation in South Whittier runs $15,000 – $40,000, and the number at the bottom of that range is a clean job on a simple roof. Here’s what pushes it up or down.
| Component | Typical range |
|---|---|
| Roof size (1,200 to 2,000+ sq ft) | $15,000 – $32,000 |
| Decking replacement (skip sheathing to solid) | $1,500 – $5,000 |
| Custom color or finish upgrade | $800 – $2,500 |
| Detached garage roof added to the job | $3,000 – $8,000 |
| Permit and inspection fees | Varies with scope |
Roof size and pitch. Square footage is the biggest driver. A steep pitch or a cut-up hip roof adds labor and waste, and a low pitch may need a different panel profile or a standing-seam system to shed water properly. Existing roof condition. If the sheathing is sound and there’s one layer of shingles to strip, it’s the low end. Rotted fascia, multiple layers, or a failing deck push toward the high end. Detached structures. A lot of these homes have a detached garage, a workshop, or a patio cover with its own roof – folding those in adds cost but usually saves money versus calling a crew out twice. Material grade and color. Standard-gauge steel in a standard finish is the budget move; aluminum in a custom color is the top end.
A written estimate from us lists tear-off and disposal, decking repair allowance, underlayment and flashing, panels or shingles, vents, and permit fees as separate line items. What’s often left out of other bids: steep-pitch labor surcharges, the sheathing replacement, and detached structures. We quote them up front so the number you see is the number you pay, and there are no change orders unless you approve them. We also offer 0% financing for 18 months and $1,000 off projects over $10,000.
See the difference
Before
After
Before
After
Before
AfterWhat South Whittier homes specifically do to a metal roof job
South Whittier is an unincorporated pocket of LA County, and that fact shapes the job before a single panel shows up. Plans and permits go through LA County Public Works rather than a city building department, which means the timeline and inspection scheduling run differently than they do in neighboring Whittier, Santa Fe Springs, or La Mirada. We build the permit window into the schedule instead of pretending it doesn’t exist. The other reality is the housing stock: most of these are 1940s – 1960s single-story stucco tract homes on 6,000 – 8,000 sq ft lots, and the roof decking is skip sheathing under old three-tab shingles. That means a metal job here almost always includes a decking overlay, and we plan for it. The detached garages off the alley and the carports tucked behind homes are common, and they often get re-roofed in the same run. On the climate side, hot dry summers and Santa Ana wind events mean a Class A assembly with ember-resistant vents is the sensible spec, and the mild winters let us work the job year-round instead of waiting for a dry spell.
Serving South Whittier, CA – Our Local Coverage Area
We serve South Whittier and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Metal Roofing in South Whittier

Most single-story homes here finish in 3 – 6 working days plus the permit and inspection window. That covers tear-off, decking, underlayment, and the panel install, with a final walk after County sign-off. Call (888) 255-8179 for a scheduling estimate specific to your roof.
Yes. Re-roofing in unincorporated South Whittier requires a permit through LA County Public Works, and the job needs a final inspection. We pull the permit for you and meet the inspector on site, so you’re not chasing paperwork. Call (888) 255-8179 if you have questions about what your project needs.
Usually yes, but the decking needs attention first. The skip sheathing common on these homes has to be overlaid with solid decking before panels go down, and any soft or rotted sheathing gets replaced. That’s structural prep, not a rebuild, and we scope it in the estimate so there’s no surprise.
Metal Roof Installation here runs $15,000 – $40,000. Roof size, decking condition, whether you’re adding a detached garage or patio cover, the panel gauge, and custom color are the drivers. Call (888) 255-8179 for an exact quote – estimates are free.
Panels carry their manufacturer finish warranty and the installation is backed by our 730-Day Done Right Promise. If the work isn’t right, we make it right. That covers workmanship, and we hand over the panel paperwork at the walkthrough.
If you’re planning a wider exterior refresh alongside the roof, homeowners often pair this with Window Replacement in South Whittier or Impact Windows & Doors in South Whittier, since the scaffolding and crews line up. It’s also common to fold the roof into a Roofing in South Whittier project when other sections need work, and you can see the full Roofing scope we handle. We cover the whole of South Whittier, ZIP 90605 included.
Get a free metal roofing estimate in South Whittier
Call (888) 255-8179 to schedule your free on-site estimate. We’ll walk the roof, measure it, check the decking from the attic side, and talk through standing seam versus stone-coated steel with real numbers in hand. You’ll get a written line-item quote with permits and inspection included, and a live person answers whether you call on a Tuesday morning or a Sunday night. No pressure, no vague pricing.
Written by the team at Groundwork Construction Co. of Downey.












