







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Wood Fence in Pico Rivera, CA: What It Takes and What It Costs
A wood fence in Pico Rivera usually runs $3,500 – $9,000 for a typical residential lot, and most jobs are built in 2 – 4 days once materials land and any permit clears. You’re choosing between cedar, redwood and pressure-treated pine, post-and-rail versus privacy style, and heights from 4 to 6 feet. Call (888) 255-8179 for a free on-site estimate with line-item pricing before anything gets ordered.
How We Build a Wood Fence in Pico Rivera, Start to Finish

The sequence is pretty consistent from job to job. Here’s what actually happens and when you’ll be asked to make a call.
Stage 1: Site visit and layout (day 1, about 60 – 90 minutes)
We walk the property line with you, check where the fence should sit relative to the lot line, and flag anything in the path: sprinkler lines, gas stubs, mature tree roots, low-voltage lighting. This is where you decide the fence line itself. If the property line is uncertain, that conversation needs to happen with your neighbor before we set a single post. We also measure total linear feet and count corners and gates, since those drive the estimate.
Stage 2: Permit and utility check (day 1 – 5, varies)
In most cases a residential wood fence under 6 feet in Pico Rivera doesn’t need a building permit, but height, placement near the front setback, and corner-lot sight triangles can change that. We confirm the rule for your address before ordering materials, and we call 811 to mark utilities before digging. If the fence is part of a full Fence Installation in Pico Rivera project that includes gates or a retaining component, the permit picture gets more involved and we handle it in the estimate.
Stage 3: Demo and post setting (day 1 – 2 of build)
Old fencing comes out and gets hauled away. Posts go in at 6- to 8-foot spacing, set in concrete, and left to cure. This is the one stage you can’t rush. Concrete needs 24 – 48 hours before it carries load, and skipping that cure time is the number one reason cheap fences lean within two years.
Stage 4: Rails, pickets and gates (day 2 – 3)
Stringers, pickets, cap rail and gate framing go up. You’ll have already picked your picket style, spacing and height by this point. This is the stage where a homeowner decision matters most: full-privacy pickets (no gaps) cost more in material and block wind harder, while a spaced or shadowbox design lets air through and looks lighter.
Stage 5: Finish and walkthrough (day 3 – 4)
We do a final level check, hang gates with proper hardware, and walk the whole run with you. Staining or sealing is scheduled separately, usually 4 – 8 weeks out so the wood can dry. You get a written closeout with what was built and the warranty on workmanship.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
The right material depends on how long you want this fence to last and how much maintenance you’ll actually do. Here’s the honest version of each:
- Cedar: The best natural rot resistance for the money. Tight grain, holds stain well, ages to a silver-gray if left bare. Runs toward the higher end of the $3,500 – $9,000 range. Suits homeowners planning to stay put for a decade or more.
- Redwood: Similar durability to cedar, slightly softer, takes a beautiful finish. Usually the most expensive option and worth it only if appearance is the priority.
- Pressure-treated pine: The value pick. Chemically treated for ground contact, readily available, accepts paint and stain well. It can shrink and check as it dries, so buy it wet and let it settle. Good for tighter budgets and for renters-adjacent situations.
- Heights: 4-foot (front-yard friendly), 5-foot (the quiet middle option), 6-foot (full privacy, the most common for backyards). Corner lots often need shorter frontage to keep sight triangles clear.
- Post type: Standard 4×4 posts handle most residential runs. 6×6 posts cost more but hold up better in wind and last longer in our hot, dry summers.
- Finish: Bare, stained, or painted. Staining adds roughly $1 – $2 per linear foot and needs a re-coat every 3 – 5 years in this climate.
What Wood Fence Costs in Pico Rivera, CA

The lead range for a standard residential wood fence here is $3,500 – $9,000. That covers most single-family lots in the ZIP codes we work: 90660, 90661 and 90662. What pushes a job toward the low or high end comes down to five variables.
- Linear footage: The single biggest driver. A 100-foot side-and-back run lands near the bottom of the range; a full 200-foot perimeter with corners pushes toward the top.
- Material grade: Pressure-treated pine sits at the low end. Cedar and redwood run $2,000 – $3,000 higher on an average lot.
- Existing fence condition: Rotting posts, buried concrete footings or overgrown root systems add demo and disposal time.
- Gates: Each gate adds cost for framing, hardware and alignment. Multiple gates compound it.
- Grade and drainage: Sloped lots need stepped panels and deeper footings, and soil that holds water means bigger concrete collars.
A written estimate from us includes demo, haul-away, posts, concrete, stringers, pickets, gate hardware, cleanup, and the permit check. It typically excludes staining or sealing (quoted separately), landscape repair beyond basic leveling, and any retaining wall the fence needs to sit on. The number we quote is the number you pay, backed by our 730-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
AfterWhat Pico Rivera Homes Specifically Do to This Job
Pico Rivera is a built-out, post-war working-class suburb where most single-family homes went up in the 1950s and ’60s. That means almost all the wood fence work here is replacement and remodel on decades-old property lines, not new-build installs. The original fences on these gridded tract streets have usually been patched two or three times before a homeowner calls us. What we find most often: posts rotted at the ground line from winter rain that pools against aging drainage, pickets warped and sun-bleached from hot inland summers and dry Santa Ana winds, and gate hardware that’s simply worn out. The local housing stock sits on narrow lots, so fence lines run tight against detached garages, side yards and air conditioning pads, and we regularly work around those without disturbing them. Because so much of Pico Rivera is owner-occupied and Spanish-speaking, we document layouts and permit scope in plain language and walk every decision through with the family before materials get ordered. Homeowners often pair a new fence with Paver Driveways in Pico Rivera when the front yard is being reworked at the same time.
Serving Pico Rivera, CA – Our Local Coverage Area
We serve Pico Rivera and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Wood Fence in Pico Rivera

Most residential wood fence jobs here finish in 2 – 4 days once materials arrive, with concrete cure time driving the back half. Small runs (under 100 feet with one gate) can wrap in 2 days. Larger perimeter jobs with multiple gates take 3 – 4. Call (888) 255-8179 for an exact schedule estimate after we see the property.
In most cases a residential wood fence under 6 feet tall does not require a building permit, but corner-lot sight triangles, front-setback placement and retaining components can change that. We confirm the specific rule for your address before ordering a single board, so you’re not the one chasing the code question. Call (888) 255-8179 to talk through your address.
Yes, in nearly every case a wood fence can be routed around existing plumbing lines, sprinkler runs and structures with a careful utility check. We call 811 before digging and adjust post placement if a line is in the way. The one thing we won’t do is build over a utility without relocating it, because the cost of hitting a gas or water line later dwarfs the cost of a small adjustment now.
A standard wood fence in Pico Rivera runs $3,500 – $9,000, depending on linear footage, material grade (pine at the low end, cedar and redwood toward the top), gate count, and site condition. Staining is separate, roughly $1 – $2 per linear foot. Call (888) 255-8179 for a free line-item estimate.
Every wood fence we build is covered by our 730-Day Done Right Promise. If a post, gate or picket fails due to workmanship within that window, we make it right. That’s one of the longest workmanship guarantees in the residential construction space, and it’s the reason we don’t cut the cure-time corner on posts.
The rest of the property scope (gates, retaining, pavers) lives on our Fence Installation hub, and Concrete Driveways & Concrete Work in Pico Rivera and Pico Rivera cover the driveways and the rest of the service area, so you can plan the whole yard at once.
Get a Free Wood Fence Estimate in Pico Rivera
We come out, walk the property line, measure the run, check for utilities and confirm the permit question, then hand you a written line-item estimate the same visit. No pressure, no vague range. Call (888) 255-8179 and a live person picks up, day or night, to schedule your free estimate.
Written by the team at Groundwork Construction Co.












