







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Whittier, CA: What It Costs and How Long It Takes
A wrought iron fence in Whittier, CA typically runs $3,500 to $9,000 for a standard residential front or side-yard run, and most jobs are finished in 2 to 4 working days once the material is on site. That number covers fabrication, posts set in concrete, finish coating, and haul-away of the old fence. Call (888) 255-8179 and we’ll walk your property line, measure the actual run, and give you a written line-item quote before anyone touches a shovel.
How an Iron Fence Goes In, Stage by Stage

An iron fence is a different animal from a wood or vinyl job. It’s fabricated to length, it’s heavy, and the posts carry real load. Here’s the sequence we run, and what you’ll be deciding at each step.
Stage 1: Site walk and layout (day 1, about 90 minutes)
We measure the run, check property lines against your plat, and look at what’s underground – irrigation lines, old footings, gas stubs. On Whittier lots this is where surprises show up, especially where a 1940s home has a fence sitting on a cracked original concrete curb. You decide the fence line and gate locations here. Nothing gets ordered until you sign off on the layout.
Stage 2: Demo and prep (day 1-2)
Old fence comes out, posts and all. If the existing footings are sound we can sometimes reuse them, but on iron we usually don’t – the new posts are heavier and the load path has to be right. We excavate new post holes to depth, set them in concrete, and let them cure. Curing is the one thing you can’t rush: a typical 24 to 48 hours before the panels go up.
Stage 3: Fabrication and delivery (3 to 10 days, before the crew returns)
Your fence is built to the measured run. This is the long pole in the schedule, and it depends on the picket style, the panel heights, and the finish. Standard galvanized-and-coated runs come faster than custom ornamental patterns. You choose the finish color and coating spec at this stage, and this is also when any gate hardware gets specified.
Stage 4: Install (1 to 2 days)
Posts get checked for plumb, panels get set and leveled, gates get hung and adjusted. We check every gate swing twice – once cold, once after a dozen open-and-close cycles – because a gate that drags after a week is a gate that wasn’t hung right on day one.
Stage 5: Walkthrough and touch-up (same day as install)
We walk the full run with you, touch up any coating nicks from handling, and hand over the gate keys or code. You sign off on the finished line before we pack up. Any punch items get scheduled before we leave the property.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Iron Fence Options You’ll Actually Choose Between
Most homeowners come in thinking “iron is iron.” It isn’t. The choices below are the ones that change both the look and the price of your Whittier fence.
- Wrought iron vs. steel ornamental: True wrought iron is hand-forged and expensive; most residential “iron” fences today are steel ornamental built to look the part. Steel holds up well and costs less. Ask which you’re getting before you compare bids – a quote that says “iron” without saying which metal isn’t a real quote.
- Picket style and spacing: Flat-top, spear-top, and basket-and-scroll patterns all cost different amounts to fabricate. Tighter picket spacing costs more and gives more privacy and security. You’ll pick a pattern and a spacing here, and it’s the single biggest visual decision.
- Height: A 4-foot run for a front-yard accent, 5 to 6 feet for a real security line. Height drives panel count, post spacing, and price.
- Coating and finish: Powder coating in black, bronze, or a custom color. A factory powder coat outlasts a field-applied paint by years in Whittier’s sun. Galvanized core plus powder coat is the combination we recommend for anything facing the afternoon sun.
- Gates and hardware: Walk gates, double drive gates, self-closing hinges, keyed latches. Gates add real cost because of the hardware and the heavier posts they need.
What Iron Fence Costs in Whittier, CA

The lead range for a residential iron fence in Whittier is $3,500 to $9,000. That covers a standard front or side-yard run with a walk gate, posts set in concrete, powder-coat finish, and cleanup. Where a job lands in that range comes down to five things:
- Linear feet: The obvious driver. Most Whittier front-yard runs fall between 60 and 120 feet.
- Existing fence condition: A rotten wood fence with sound footings is a faster demo than a rusted iron fence welded to old posts that have to be cut out.
- Grade and pattern: Standard steel ornamental sits at the low end; custom ornamental and true wrought iron push toward the top.
- Gates: Each gate adds hardware cost, and drive gates need heavier posts and framing.
- Site access and slope: A level lot is a straight install. A sloped yard or a tight side-yard access changes the labor and can push a job $500 to $1,500 higher.
A written estimate should spell out linear feet, post spacing, material grade, coating spec, gate count, and cleanup. What it typically won’t include: concrete repair to a cracked curb, root removal, or a survey if one turns out to be needed. We flag anything like that before the contract is signed, not after.
See the difference
Before
After
Before
After
Before
AfterWhat Whittier Homes Specifically Do to This Job
Whittier is two different towns stacked on top of each other, and which one you live in changes the fence job. In the historic Uptown core (90601) you’re working around 1910s to 1950s Craftsman and Spanish Colonial homes, many inside a state-designated historic overlay – and a front-yard fence that changes the streetscape there can pull a design-review permit that adds weeks to the front end of the project. Out in the mid-century ranch tracts in the eastern ZIPs (90604, 90606), the same fence is a same-week pull, and what you’re usually dealing with instead is a slab-on-grade lot where the original concrete curb has cracked or heaved from root pressure. The heat is the other factor: Whittier’s Santa Ana wind episodes and dry summers are hard on a finish coat, so we lean on factory powder coat over galvanized core rather than field-painted iron on any run facing west or south.
Serving Whittier, CA – Our Local Coverage Area
We serve Whittier and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Iron Fence in Whittier

Install day is 1 to 2 days, but the full project from signed contract to finished fence usually runs 2 to 4 weeks because of fabrication and delivery. Call (888) 255-8179 and we’ll give you a dated schedule, not a range.
Most residential iron fences under 6 feet fall under the standard fence permit, but properties inside the Uptown historic overlay can trigger design review even for a short run. We check your address before we quote, so the permit scope is in the number from day one. Call (888) 255-8179 and we’ll tell you what your specific address requires.
In most cases yes – iron fences go in on post holes, not a continuous footing, so the disruption is a line of holes rather than a full trench. Existing irrigation, gas lines, and old footings are the things we check before digging. If something’s in the way, we flag it before we start. Call (888) 255-8179 to schedule the site walk.
A standard residential iron fence in Whittier runs $3,500 to $9,000 depending on linear feet, picket pattern, height, gates, and site access. Call (888) 255-8179 for an exact quote – the estimate is free and the quote is line-item, so you can see where the money goes.
Every fence we install is covered by our 730-Day Done Right Promise – if it’s not done right, we make it right. That covers workmanship for two full years. Call (888) 255-8179 and we’ll walk you through what the warranty covers.
Get a Free Iron Fence Estimate in Whittier
Call (888) 255-8179 for a free on-site estimate for your iron fence in Whittier. We’ll measure the run, check your address against Whittier’s permit requirements, and hand you a written line-item quote with the fence line, post spacing, finish spec, and gate count spelled out. A live person answers, 24/7. No surprises, no change orders.
Written by the team at Groundwork Construction Co. of Downey.












