







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Backsplash, Tile & Flooring in Pico Rivera: What It Takes and What It Costs
Most backsplash, tile and flooring jobs in Pico Rivera run $14,000 – $45,000 for a full kitchen scope, or $800 – $2,500 for a backsplash on its own, with countertop and floor work layered in between. A backsplash alone is a 2 – 3 day job; floors and tile together usually take 5 – 10 working days depending on square footage and how much prep the subfloor needs. Call (888) 255-8179 for a free on-site estimate and a written line-item quote.
How We Run a Backsplash, Tile & Flooring Job, Stage by Stage

Tile work rewards patience and punishes shortcuts. Here’s what actually happens, day by day, so you know what to expect and what we’ll ask you to decide.
Stage 1: Site walk and material takeoff (day 1)
We measure every surface that’s getting tile: backsplash runs, floor square footage, and any transitions at doorways or thresholds. You decide on tile size and material here, because layout and grout choices flow from that. We also check the subfloor for deflection and moisture, and inspect the wall behind the backsplash for old adhesive, water damage, or out-of-plumb framing. Half a day.
Stage 2: Demo and prep (days 2 – 3)
Old backsplash comes off, old flooring comes up, and we haul it out. This is where older homes surprise people: a 1950s – 60s Pico Rivera tract home often has a second layer of vinyl or tile under the visible floor, and removing it adds time and disposal cost. We level the subfloor, install cement backer board where it’s needed, and prime walls before any tile goes up. One to two days.
Stage 3: Layout and dry-fit (day 3 or 4)
Before a single tile is set, we lay out the pattern dry so you can see grout line width, where cuts land, and how the backsplash meets the countertop and cabinet edges. You approve the layout. We check that outlet and switch plates will sit flush and that the tile pattern reads correctly across the full run, not just in one corner.
Stage 4: Setting tile (days 4 – 7)
Floor tile goes down first, then backsplash, so we’re not walking on fresh wall work. Thin-set cure time matters: we don’t grout until the mortar has set properly, usually the next day. Larger-format tile takes longer to level; mosaic and small-format tile takes longer to set but is more forgiving on uneven walls. Three to four days for a typical kitchen floor and backsplash combination.
Stage 5: Grout, seal, and final walkthrough (days 7 – 10)
Grout goes in, gets sealed where the material calls for it, and we reinstall outlet covers and any trim. Then we walk the job with you, checking every joint and transition. Your sign-off is the last step, and the 730-Day Done Right Promise covers the workmanship from there.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
- Ceramic vs. porcelain floor tile. Ceramic is the budget-friendly pick and works fine in low-traffic kitchens; porcelain is denser, more water-resistant, and holds up better in a busy household. Porcelain costs more per square foot but often lasts longer.
- Subway vs. larger-format backsplash. Classic 3×6 subway tile is forgiving on imperfect walls and easy to repair; large-format slabs look modern but demand a perfectly flat wall, which sometimes means extra prep cost.
- Grout line width. Narrow lines (1/16″) look cleaner but are less tolerant of tile size variation; wider lines (1/8″ – 3/16″) hide imperfections and are easier to keep clean over the long run.
- Natural stone vs. manufactured. Marble and travertine bring warmth and movement but need sealing and show stains; quartz and porcelain tile mimic the look with almost no maintenance and cost less over time.
- Flooring transitions. Matching a tile floor to adjacent hardwood or vinyl takes a transition strip or a custom cut. We size this at the estimate stage so it’s not a surprise line item later.
- Fixtures that pair with the job. If you’re also swapping a sink or faucet, brands like Kohler and Delta are common picks in Pico Rivera kitchens and pair cleanly with a new backsplash run.
What Backsplash, Tile & Flooring Costs in Pico Rivera, CA

Expect $14,000 – $45,000 for a full kitchen backsplash, tile, and flooring scope in Pico Rivera, with a standalone backsplash at $800 – $2,500 and cabinet-adjacent countertop work at $2,000 – $6,500 if you’re pairing it. Here’s what moves the number:
| Scope | Typical Range |
|---|---|
| Backsplash installation | $800 – $2,500 |
| Countertop installation | $2,000 – $6,500 |
| Full kitchen backsplash, tile & flooring | $14,000 – $45,000 |
Four things push a job to the low or high end. Square footage is the biggest lever: a galley kitchen floor is a different job than a full open-plan kitchen. Existing condition matters most in older Pico Rivera homes, where a second subfloor layer or water-damaged wall adds prep days. Relocating plumbing or electrical (moving a sink, adding outlets behind the backsplash) adds cost and sometimes a permit. Material grade: porcelain and natural stone run higher than ceramic. A written estimate covers tile, thin-set, grout, backer board, demo, and disposal. It typically excludes structural repairs, plumbing relocations, and permit fees unless called out.
See the difference
Before
After
Before
After
Before
AfterWhat Pico Rivera Homes Specifically Do to This Job
Pico Rivera is a built-out, post-war suburb where most single-family homes went up in the 1950s and 1960s, so nearly every backsplash and tile job here is a remodel inside an existing tract home, not new construction. That means older subfloors, walls that aren’t perfectly plumb, and sometimes a second layer of flooring hiding underneath. We regularly pull permits for remodels rather than tract builds, and we navigate older LA County code requirements as a matter of course. The dry inland heat and Santa Ana winds don’t affect interior tile much, but they do stress exterior stucco and roofing on the same homes, which is worth knowing if you’re planning broader work. Homeowners here tend to stay put for decades, so we build tile work to last that long.
Serving Pico Rivera, CA – Our Local Coverage Area
We serve Pico Rivera and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked About Backsplash, Tile & Flooring in Pico Rivera

A standalone backsplash takes 2 – 3 days; a combined kitchen floor and backsplash runs 5 – 10 working days depending on square footage and subfloor prep. Call (888) 255-8179 for a timeline specific to your kitchen.
Cosmetic tile and backsplash work generally doesn’t require a permit, but relocating plumbing or electrical behind the wall does. We confirm what your specific job needs and pull permits where required.
Yes. Most backsplash jobs are surface work that leaves plumbing and framing untouched. If you want to relocate a sink or add outlets, that’s a different scope and we’ll price it separately.
Backsplash alone runs $800 – $2,500, countertops $2,000 – $6,500, and a full kitchen tile and flooring scope $14,000 – $45,000. Call (888) 255-8179 for an exact quote, free of charge.
Every backsplash, tile and flooring job is backed by our 730-Day Done Right Promise. If something isn’t right, we make it right.
Get a Free Backsplash, Tile & Flooring Estimate in Pico Rivera
We’ll walk your kitchen, measure every surface, and hand you a written line-item quote with no surprises. This is also where homeowners often pair the job with Vanities, Tile & Fixtures in Pico Rivera or a broader Kitchen Remodeling in Pico Rivera scope, and we’re glad to talk through Tub-to-Shower Conversion in Pico Rivera if you’re working through the house room by room. Call (888) 255-8179 to schedule your free estimate.
Written by the team at Groundwork Construction Co. of Downey.












