







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tub-to-Shower Conversion in Pico Rivera: What the Job Actually Involves
A tub-to-shower conversion in Pico Rivera typically runs $3,500 to $10,000 and takes three to seven working days from demo to final caulk. The job means removing the existing tub and its surround, reworking the drain and valve to fit a shower pan or tiled base, waterproofing the wet area, and setting a new shower with a proper permit on record. Most Pico Rivera homes we open up are 1950s and 60s tract builds, so the real work is what’s behind the tub wall. Call (888) 255-8179 for a free on-site estimate and a written, line-item scope before anything gets torn out.
How a Tub-to-Shower Conversion Runs, Stage by Stage

Every conversion follows the same spine, whether it’s a hall bath off Rosemead Boulevard or a master bath near Smith Park. Here’s what the calendar looks like and where you make decisions.
Stage 1: On-site measure and scope (day 0, about 60 minutes)
We measure the alcove, check the drain location and valve height, and open the access panel or look from below where possible to see what the plumbing is made of. You decide the shower type here: tiled base versus prefabricated pan, and framed glass versus a curtain-and-rod setup. This is also when we confirm whether the permit will be an over-the-counter minor remodel or a fuller scope.
Stage 2: Demo and inspection (day 1, roughly 4 to 6 hours)
The tub, surround, and any drywall come out. We cut back to sound substrate and, on older Pico Rivera homes, this is the moment we find out whether there’s water damage under the tub lip or a cast-iron drain that’s rusted through. You approve any hidden-condition add before we continue, in writing.
Stage 3: Rough-in plumbing and permit inspection (days 1 to 2)
The drain gets relocated for the new pan, the valve body is set to code height, and the rough plumbing is inspected if the permit scope calls for it. You choose the valve and trim here, and we walk you through pressure-balance versus thermostatic options.
Stage 4: Waterproofing and walls (days 2 to 3)
Cement board or a bonded waterproof membrane goes up, seams get taped and sealed, and the pan is packed or set. Waterproofing is where cheap conversions fail, so this stage gets the most inspection time. You pick tile or panel finishes before this stage so the material is on site.
Stage 5: Tile, fixtures, glass, and punch (days 3 to 7)
Tile or panel install, grout and caulk, valve trim, drain cover, and glass or curtain. We test the water for a full cycle, check the slope drains fully, and do a final walkthrough with you to sign off. Most Pico Rivera conversions close out in this window unless we’ve hit a structural or drain surprise.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between, and What Each One Really Costs You
You’re deciding on four or five items, and each has an honest trade-off. Here’s how we frame them on the estimate.
- Prefabricated acrylic or fiberglass pan and walls: the economical path, usually landing in the lower half of the range. It goes in fast, cleans easily, and holds up well, but it won’t match a custom tile look and can feel thinner underfoot.
- Tiled shower with a mud-set or foam pan: the durable, high-end path and the top of the range. Tile choices are wide, and a correctly waterproofed tiled shower can last decades, but it takes more days and more skill to get right.
- Framed glass, frameless glass, or curtain rod: frameless glass runs more but opens the room up and looks clean; framed glass is the middle option; a curtain rod is the budget pick and easiest to maintain.
- Valve and trim: a pressure-balance valve is standard and fine for most homes; a thermostatic valve stops temperature swings and is worth it if you have kids or a shared wall with the water heater.
- Grab bars and a bench: if this shower is for aging-in-place family members, we rough in blocking during stage 4 so the bars anchor to structure, not tile.
We stock and specify materials from partners like Kohler for valve and trim, so you get a known-quality fixture rather than the cheapest thing on the shelf.
What Tub-to-Shower Conversion Costs in Pico Rivera, CA

Expect $3,500 to $10,000 for a tub-to-shower conversion in Pico Rivera. That range is real, not a teaser, and the variables below explain where your job lands.
- Size of the alcove: a standard 60-inch tub replacement sits near the low end; a wider or walk-in configuration pushes up.
- Condition behind the wall: rusted cast-iron drains, soft subfloor, or water-damaged studs add real cost, and we quote them in writing before touching anything.
- Plumbing relocation: moving the drain and valve is doable but adds labor and inspection.
- Material grade: acrylic pan and walls vs. tiled with premium tile and a frameless glass door is the single biggest swing.
- Permit scope: a full plumbing rough-in and inspection costs more than a finish-only swap.
Your written estimate itemizes demo, rough-in, waterproofing, tile or panel, fixtures, glass, permit, and cleanup. What typically isn’t included: hidden rot or structural repair, fixture upgrades you request mid-job, and HOA fees. Households budgeting a bigger package can pair this with our Bathroom Remodeling service and get one scope for the room. Our 730-Day Done Right Promise and Upfront pricing, no surprises apply to every conversion we do.
See the difference
Before
After
Before
After
Before
AfterWhat Pico Rivera Homes Specifically Do to This Job
Pico Rivera is a built-out, post-war suburb across ZIP codes 90660, 90661, and 90662, and nearly every single-family home here went up in the 1950s or 60s. That means almost all our work is remodel, not new build, and it’s owner-occupied by families who stay in the home for decades – so the conversion has to be right the first time, not the fastest. Off the gridded streets around Rivera Park and along Slauson Avenue, we regularly find original cast-iron drain assemblies and galvanized supply lines behind the tub wall, and a wet winter or a slow leak has often already rotted the subfloor. The Spanish-language owner-occupied tract homes here also mean we coordinate permits with older LA County code paths for remodels rather than tract new builds, and we walk through the inspection schedule with you in plain language. Homeowners often pair this with Metal Roofing in Pico Rivera or Tile Roofing in Pico Rivera when the same dry-rot or drainage issue shows up outside. We cover the full town under our Pico Rivera service area, and if the conversion is part of a full Bathroom Remodeling in Pico Rivera, we fold it into one scope and one crew.
Serving Pico Rivera, CA – Our Local Coverage Area
We serve Pico Rivera and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Tub-to-Shower Conversion in Pico Rivera

Most take three to seven working days from demo to final caulk. A prefabricated acrylic conversion usually lands closer to three to four days; a tiled shower with frameless glass runs five to seven. Hidden plumbing or subfloor damage can extend it, and we tell you before we keep going.
Yes, virtually always – relocating the drain or valve and altering the plumbing triggers a permit and an inspection. We pull the permit and walk through the inspection stages with you. Skipping it can complicate a future sale and void insurance coverage on the plumbing, and your written estimate states the permit scope up front.
In many cases, yes. If the existing drain and valve can stay within a few inches, we can set a shower pan over the same footprint and avoid relocation. If the drain has to shift more than that, we quote it and pull the permit to cover it – a change order only with your written approval.
The range is $3,500 to $10,000, with the low end being an acrylic pan-and-wall swap and the high end a tiled shower with premium valve, trim, and frameless glass. Call (888) 255-8179 for an exact written estimate – estimates are free and itemized.
Every conversion is covered by our 730-Day Done Right Promise – if it’s not done right, we make it right, on the workmanship for the full 730 days. Manufacturer warranties cover the fixtures and glass separately. We put the warranty in writing, not in a brochure fine print.
Get a Free Tub-to-Shower Conversion Estimate in Pico Rivera
A free on-site estimate for your tub-to-shower conversion in Pico Rivera starts with a call to (888) 255-8179 – a live person answers, around the clock, not a voicemail box. We’ll measure the alcove, check the plumbing, and hand you a written, itemized scope with the price locked. Our background-checked, uniformed technicians handle the work, and the 730-Day Done Right Promise stands behind it. From foundation to finish line, one crew.
Written by the team at Groundwork Construction Co.












